Aralin 5/10 · 17 salita · 0 natutunan
Electronic components and PCBs
Mga elektronikong component at PCB
diyodo
a semiconductor component that allows current to flow in one direction only
Fit a diode across the relay coil to protect the transistor.
Maglagay ng diyodo sa magkabilang dulo ng coil ng relay upang maprotektahan ang transistor.
Use the diode test function on the multimeter to check it.
Kasingkahuluganrectifiersemiconductor dioderesistor, resistensya
a component that limits the current in a circuit by providing a fixed amount of resistance
Read the colour bands to find the value of the resistor.
Basahin ang mga kulay na guhit upang malaman ang halaga ng resistor.
Add a resistor in series to limit the current through the LED.
Kasingkahuluganresistanceelectrical resistorKasalungatconductorsuperconductorsemiconductor, semikonduktor
a material such as silicon that conducts electricity only under certain conditions, used to make diodes, transistors and chips
Silicon is the most widely used semiconductor in electronics.
Ang silicon ang pinakamalawak na ginagamit na semiconductor sa electronics.
Heat is the main enemy of semiconductor devices in power equipment.
Kasingkahulugansolid-state devicemicrochipKasalungatconductorinsulatorsolder, pagsasalda
a soft metal alloy that is melted to join wires and component leads electrically
A cracked solder joint caused the display to flicker.
Ang basag na solder joint ang nagpakislap sa display.
We switched to lead-free solder to meet export rules.
KasingkahuluganbrazeweldfusejoinKasalungatdisconnectseparatedetachtransistor
a semiconductor component used to switch or amplify electrical signals
The output transistor switches the relay coil on and off.
Binubuksan at pinapatay ng output transistor ang coil ng relay.
A shorted transistor was found on the driver board.
Kasingkahulugansemiconductoramplifierelectronic componentKasalungatvacuum tuberesistorcapacitorkapasitor, capacitor
a component that stores electrical charge for a short time and releases it, used for filtering and timing
The power supply failed because an electrolytic capacitor had dried out.
Nasira ang power supply dahil natuyo ang isang electrolytic capacitor.
Always discharge large capacitors before touching the circuit board.
Kasingkahulugancondenserelectrical storage deviceKasalungatresistorinductorinduktor, likaw na panginduksiyon
a coil of wire that stores energy in a magnetic field and resists changes in current
The inductor in the filter blocks high-frequency noise.
Hinaharang ng induktor sa filter ang ingay na mataas ang frequency.
A small inductor smooths the output current of the converter.
LED, diyodong naglalabas ng liwanag
light-emitting diode: a semiconductor component that gives out light when current passes through it
The green LED on the module shows that power is on.
Ipinapakita ng berdeng LED sa module na may kuryente.
Replacing the old lamps with LED fittings cut lighting costs by half.
IC, pinagsamang sirkito
a small chip containing many electronic components such as transistors and resistors, built as one unit
The timer function is handled by a single integrated circuit.
Isang integrated circuit lamang ang humahawak sa tungkulin ng timer.
Handle each integrated circuit carefully to avoid static damage.
regulator ng boltahe, tagapirmi ng boltahe
a component or circuit that keeps the output voltage steady even when the input or load changes
A 5 volt voltage regulator supplies the logic part of the board.
Isang 5 volt na voltage regulator ang nagsusuplay sa logic na bahagi ng board.
The voltage regulator was very hot because the input voltage was too high.
potensiyometro, nababagong resistor
a variable resistor with a knob or screw used to adjust voltage or settings in a circuit
Turn the potentiometer slowly to adjust the motor speed.
Dahan-dahang paikutin ang potensiyometro upang ayusin ang bilis ng motor.
The sensor sensitivity is set with a small potentiometer on the board.
PCB, nakalimbag na sirkitong tabla
printed circuit board: a flat board with copper tracks that holds and connects electronic components
The PCB was cracked near the connector after the unit was dropped.
Nabitak ang PCB malapit sa connector matapos mahulog ang unit.
Our factory does PCB assembly for several electronics brands.
landas na tanso, bakas ng tanso
a thin copper line on a printed circuit board that connects components electrically
A burnt trace on the board was repaired with a short wire.
Inayos ng maikling alambre ang nasunog na landas na tanso sa board.
Make the power traces wider so they can carry more current.
SMD, sangkap na nakadikit sa ibabaw ng board
surface-mount device: a small component soldered directly onto the surface of a circuit board, without wire leads through holes
SMD parts are placed on the board by a pick-and-place machine.
Ang mga SMD na piyesa ay inilalagay sa board ng isang pick-and-place machine.
Replacing an SMD capacitor by hand needs a fine soldering tip.
pasuot-butas, nakatusok sa butas
describing components whose wire leads go through holes in a circuit board and are soldered on the other side
Large connectors are still through-hole parts for extra strength.
Through-hole pa rin ang malalaking connector para sa dagdag na tibay.
Through-hole components are easier to replace during field repairs.
panghinang, pangsolder
a hand tool with a hot metal tip used to melt solder and join components
Set the soldering iron to about 350 degrees for this work.
Itakda ang soldering iron sa humigit-kumulang 350 degrees para sa gawaing ito.
Clean the soldering iron tip on a damp sponge between joints.
pampalamig na metal, taga-alis ng init
a metal part with fins attached to a component to carry heat away and keep it cool
Apply thermal paste before fixing the transistor to the heat sink.
Maglagay ng thermal paste bago ikabit ang transistor sa heat sink.
Dust on the heat sink made the drive shut down from overheating.
