Skip to content

Lesson 5/10 · 17 words · 0 learned

Electronic components and PCBs

  1. 1

    diode(noun)

    /ˈdaɪəʊd/

    a semiconductor component that allows current to flow in one direction only

    Fit a diode across the relay coil to protect the transistor.

    Use the diode test function on the multimeter to check it.

    Synonymsrectifiersemiconductor diode
  2. 2

    resistor(noun)

    /rɪˈzɪstər/

    a component that limits the current in a circuit by providing a fixed amount of resistance

    Read the colour bands to find the value of the resistor.

    Add a resistor in series to limit the current through the LED.

    Synonymsresistanceelectrical resistor
    Antonymsconductorsuperconductor
  3. 3

    semiconductor(noun)

    /ˈsemikəndʌktər/

    a material such as silicon that conducts electricity only under certain conditions, used to make diodes, transistors and chips

    Silicon is the most widely used semiconductor in electronics.

    Heat is the main enemy of semiconductor devices in power equipment.

    Synonymssolid-state devicemicrochip
    Antonymsconductorinsulator
  4. 4

    solder(noun)

    /ˈsɑːdər/

    a soft metal alloy that is melted to join wires and component leads electrically

    A cracked solder joint caused the display to flicker.

    We switched to lead-free solder to meet export rules.

    Synonymsbrazeweldfusejoin
    Antonymsdisconnectseparatedetach
  5. 5

    transistor(noun)

    /trænˈzɪstər/

    a semiconductor component used to switch or amplify electrical signals

    The output transistor switches the relay coil on and off.

    A shorted transistor was found on the driver board.

    Synonymssemiconductoramplifierelectronic component
    Antonymsvacuum tuberesistorcapacitor
  6. 6

    capacitor(noun)

    /kəˈpæsɪtər/

    a component that stores electrical charge for a short time and releases it, used for filtering and timing

    The power supply failed because an electrolytic capacitor had dried out.

    Always discharge large capacitors before touching the circuit board.

    Synonymscondenserelectrical storage device
    Antonymsresistorinductor
  7. 7

    inductor(noun)

    /ɪnˈdʌktə(r)/

    a coil of wire that stores energy in a magnetic field and resists changes in current

    The inductor in the filter blocks high-frequency noise.

    A small inductor smooths the output current of the converter.

  8. 8

    LED(abbreviation)

    /ˌel iː ˈdiː/

    light-emitting diode: a semiconductor component that gives out light when current passes through it

    The green LED on the module shows that power is on.

    Replacing the old lamps with LED fittings cut lighting costs by half.

  9. 9

    integrated circuit(noun)

    /ˌɪntɪɡreɪtɪd ˈsɜːkɪt/

    a small chip containing many electronic components such as transistors and resistors, built as one unit

    The timer function is handled by a single integrated circuit.

    Handle each integrated circuit carefully to avoid static damage.

  10. 10

    voltage regulator(noun)

    /ˈvəʊltɪdʒ ˌreɡjuleɪtə(r)/

    a component or circuit that keeps the output voltage steady even when the input or load changes

    A 5 volt voltage regulator supplies the logic part of the board.

    The voltage regulator was very hot because the input voltage was too high.

  11. 11

    potentiometer(noun)

    /pəˌtenʃiˈɒmɪtə(r)/

    a variable resistor with a knob or screw used to adjust voltage or settings in a circuit

    Turn the potentiometer slowly to adjust the motor speed.

    The sensor sensitivity is set with a small potentiometer on the board.

  12. 12

    PCB(abbreviation)

    /ˌpiː siː ˈbiː/

    printed circuit board: a flat board with copper tracks that holds and connects electronic components

    The PCB was cracked near the connector after the unit was dropped.

    Our factory does PCB assembly for several electronics brands.

  13. 13

    trace(noun)

    /treɪs/

    a thin copper line on a printed circuit board that connects components electrically

    A burnt trace on the board was repaired with a short wire.

    Make the power traces wider so they can carry more current.

  14. 14

    SMD(abbreviation)

    /ˌes em ˈdiː/

    surface-mount device: a small component soldered directly onto the surface of a circuit board, without wire leads through holes

    SMD parts are placed on the board by a pick-and-place machine.

    Replacing an SMD capacitor by hand needs a fine soldering tip.

  15. 15

    through-hole(adjective)

    /ˈθruː həʊl/

    describing components whose wire leads go through holes in a circuit board and are soldered on the other side

    Large connectors are still through-hole parts for extra strength.

    Through-hole components are easier to replace during field repairs.

  16. 16

    soldering iron(noun)

    /ˈsəʊldərɪŋ ˌaɪən/

    a hand tool with a hot metal tip used to melt solder and join components

    Set the soldering iron to about 350 degrees for this work.

    Clean the soldering iron tip on a damp sponge between joints.

  17. 17

    heat sink(noun)

    /ˈhiːt sɪŋk/

    a metal part with fins attached to a component to carry heat away and keep it cool

    Apply thermal paste before fixing the transistor to the heat sink.

    Dust on the heat sink made the drive shut down from overheating.