Skip to content

Lesson 2/10 · 16 words · 0 learned

Wiring and installation

  1. 1

    cable(noun)

    /ˈkeɪbl/

    one or more insulated conductors inside a protective outer cover, used to carry electricity

    We need to lay a 95 square millimetre cable from the transformer to the main board.

    Check the cable for cuts before pulling it through the conduit.

    Synonymswirecordropestrandline
    Antonymswireless
  2. 2

    termination(noun)

    /ˌtɜːmɪˈneɪʃn/

    the ending of an employment contract, by the employer, the employee or both sides

    The termination of his contract takes effect at the end of the month.

    HR must check the legal reasons for termination before sending the letter.

  3. 3

    conduit(noun)

    /ˈkɒndjuɪt/

    a metal or plastic pipe that wires are pulled through to protect them

    All wiring in the plant room must run in galvanised steel conduit.

    The electricians fixed the conduit to the ceiling before pulling the wires.

  4. 4

    cable tray(noun)

    /ˈkeɪbl treɪ/

    an open metal support, like a long shelf, used to carry and route many cables

    The power cables and control cables run on separate cable trays.

    Do not overload the cable tray; leave space for future cables.

  5. 5

    trunking(noun)

    /ˈtrʌŋkɪŋ/

    an enclosed channel with a removable lid, fixed to walls or ceilings to hold cables

    Put the lid back on the trunking after adding the new cables.

    Surface trunking was used because the walls could not be chased.

  6. 6

    junction box(noun)

    /ˈdʒʌŋkʃn bɒks/

    a small enclosed box where wires are joined or split into different circuits

    All cable joints must be made inside an accessible junction box.

    Use a waterproof junction box for the outdoor lighting.

  7. 7

    socket outlet(noun)

    /ˈsɒkɪt ˌaʊtlet/

    a device fixed to a wall or panel into which a plug is inserted to get power

    Each workstation needs two socket outlets near the bench.

    The socket outlet in the kitchen was scorched by a loose connection.

  8. 8

    light switch(noun)

    /ˈlaɪt swɪtʃ/

    a switch on a wall used to turn lights on and off

    Mount the light switch 1.2 metres above the finished floor.

    A two-way light switch lets you control the stair lights from both floors.

  9. 9

    terminal block(noun)

    /ˈtɜːmɪnl blɒk/

    an insulated block with screw or spring clamps used to connect wires securely inside a panel

    Land the field wires on the terminal block at the bottom of the panel.

    Each terminal block is numbered to match the wiring diagram.

  10. 10

    cable gland(noun)

    /ˈkeɪbl ɡlænd/

    a fitting that holds and seals a cable where it enters an enclosure or panel

    Tighten the cable gland so dust and water cannot enter the motor box.

    Armoured cables need a cable gland that also earths the armour.

  11. 11

    cable lug(noun)

    /ˈkeɪbl lʌɡ/

    a metal end fitting pressed onto a cable so it can be bolted to a terminal or busbar

    Use the correct size cable lug for the 70 square millimetre conductor.

    The cable lug was loose, so the busbar connection overheated.

  12. 12

    crimp(verb)

    /krɪmp/

    to join a connector or lug to a wire by squeezing it tightly with a special tool

    Crimp the ferrule onto the wire before inserting it into the terminal.

    Badly crimped lugs are a common cause of hot joints.

  13. 13

    strip(verb)

    /strɪp/

    to remove the insulation from the end of a wire so that it can be connected

    Strip about ten millimetres of insulation from each wire.

    Be careful not to nick the copper when you strip the cable.

  14. 14

    cross-sectional area(noun)

    /ˌkrɒs ˌsekʃənl ˈeəriə/

    the size of a conductor measured across its cut end, in square millimetres, which shows how much current it can carry

    The cable's cross-sectional area must suit the load current and the cable length.

    A 2.5 square millimetre cross-sectional area is typical for socket circuits.

  15. 15

    voltage drop(noun)

    /ˈvəʊltɪdʒ drɒp/

    the loss of voltage along a cable or component because of its resistance

    On long cable runs, check the voltage drop does not exceed five percent.

    The pump would not start because of a high voltage drop in the feeder.

  16. 16

    sheath(noun)

    /ʃiːθ/

    the outer protective layer of a cable that covers the insulated cores

    The cable sheath was damaged where it rubbed against the steel beam.

    Keep the outer sheath inside the gland so no bare cores are visible.