Skip to content

Lesson 10/10 · 15 words · 0 learned

Electrical safety

  1. 1

    electric shock(noun)

    /ɪˈlektrɪk ʃɑːk/

    the injury or sudden pain caused when electric current passes through a person's body

    He received an electric shock from a damaged extension lead.

    RCDs greatly reduce the risk of a fatal electric shock.

    Synonymselectrical shockelectrocutionjolt
    Antonymsnone
  2. 2

    electrocution(noun)

    /ɪˌlektrəˈkjuːʃn/

    death or serious injury caused by electric current passing through the body

    Working near overhead lines without a permit risks electrocution.

    The investigation found that the electrocution was caused by a missing earth.

    Synonymselectric shockelectrocution
    Antonymsrevivalresuscitation
  3. 3

    lockout/tagout(noun)

    /lɑːkaʊt/ˈtæɡaʊt/

    a safety procedure where a machine's energy sources are switched off, locked and tagged before maintenance work

    Apply lockout/tagout before you put your hands inside the machine.

    Every maintenance technician has a personal lock for lockout/tagout.

    SynonymsControl of Hazardous EnergyEnergy Isolation
    AntonymsActivationEnergization
  4. 4

    earthing(noun)

    /ˈɜːθɪŋ/

    connecting metal parts of an installation to the ground so that fault current flows safely away

    Good earthing makes sure the breaker trips quickly during a fault.

    Check the earthing of all metal cable trays before handover.

  5. 5

    equipotential bonding(noun)

    /ˌekwipəˈtenʃl ˈbɒndɪŋ/

    connecting exposed metal parts and pipes together so they stay at the same voltage and cannot cause a shock

    Equipotential bonding is required for the water and gas pipes.

    The bathroom failed inspection because the equipotential bonding was missing.

  6. 6

    live(adjective)

    /laɪv/

    connected to a source of electricity and able to give a shock

    Treat every conductor as live until you have tested it.

    Live working is allowed only with a special permit and trained staff.

  7. 7

    de-energise(verb)

    /diː ˈenədʒaɪz/

    to disconnect equipment or a circuit from its power supply so that it is no longer live

    De-energise the panel and prove it dead before removing any covers.

    The feeder was de-energised for six hours during the maintenance work.

  8. 8

    safe isolation(noun)

    /ˌseɪf ˌaɪsəˈleɪʃn/

    the procedure of switching off, locking off and testing equipment to prove it is dead before work starts

    Follow the safe isolation procedure before working on any circuit.

    Safe isolation includes testing your voltage tester on a known live source.

  9. 9

    permit to work(noun)

    /ˌpɜːmɪt tə ˈwɜːk/

    a written approval that states what work may be done, the hazards and the safety steps that must be taken

    No one may open the switchgear without a signed permit to work.

    The permit to work lists the isolation points and earthing locations.

  10. 10

    arc flash(noun)

    /ˈɑːk flæʃ/

    a sudden explosion of heat and light caused by a fault current jumping through the air between conductors

    Wear an arc flash suit when racking out the breaker.

    An arc flash can cause severe burns even several metres away.

  11. 11

    insulated gloves(noun)

    /ˌɪnsjuleɪtɪd ˈɡlʌvz/

    rubber gloves rated for a certain voltage that protect the hands from electric shock

    Inspect your insulated gloves for holes before every use.

    Insulated gloves must be tested in a lab every six months.

  12. 12

    high voltage(noun)

    /ˌhaɪ ˈvəʊltɪdʒ/

    voltage high enough to need special equipment and training, usually above 1,000 volts AC

    Only authorised persons may work on high voltage equipment.

    Danger signs warn of high voltage on the transformer fence.

  13. 13

    low voltage(noun)

    /ˌləʊ ˈvəʊltɪdʒ/

    voltage used in ordinary buildings and machines, usually up to 1,000 volts AC

    The low voltage side of the transformer supplies the main switchboard.

    She is qualified to work on low voltage installations up to 1,000 volts.

  14. 14

    double insulation(noun)

    /ˌdʌbl ˌɪnsjuˈleɪʃn/

    a design with two layers of insulation so that a tool or appliance needs no earth connection

    Power tools with double insulation have a square-in-a-square symbol.

    Double insulation protects the user even if one layer fails.

  15. 15

    earth leakage(noun)

    /ˌɜːθ ˈliːkɪdʒ/

    a small current that flows to earth through damaged insulation instead of returning through the neutral

    Moisture in the cable caused earth leakage and tripped the RCD.

    The earth leakage relay alarms at 300 milliamps on the main feeder.