Pelajaran 2/10 · 15 kata · 0 sudah hafal
Hand and power tools
Perkakas tangan dan perkakas listrik
tang
a hand tool with two handles and jaws, used for gripping, bending or cutting wire and small parts
Use long-nose pliers to fit the spring into the narrow slot.
Gunakan tang lancip untuk memasang pegas ke dalam celah yang sempit.
He cut the locking wire with a pair of pliers.
Sinonimnipperstweezers (depending on the type)Antonimnone (Pliers are a specific tool with no direct opposite)kunci pas
a metal hand tool with a shaped end for holding and turning nuts and bolts
Pass me the 17 mm spanner so I can loosen this nut.
Tolong berikan kunci pas 17 mm agar saya bisa mengendurkan mur ini.
Use a ring spanner on tight nuts so it does not slip.
Sinonimwrenchadjustable wrenchopen-end wrenchbox-end wrenchAntonimnonepahat
a hand tool with a sharp flat end, hit with a hammer to cut or shape metal, wood or stone
He used a cold chisel to cut off the rusted bolt head.
Ia memakai pahat dingin untuk memotong kepala baut yang berkarat.
Wear safety glasses when you strike a chisel with a hammer.
Sinonimcutting toolgraverscraperAntonimfilleradhesivekunci momen, kunci torsi
a wrench that lets you tighten a bolt to an exact turning force set in newton metres
Tighten the cylinder head bolts with a torque wrench set to 90 Nm.
Kencangkan baut kepala silinder dengan kunci momen yang diatur pada 90 Nm.
Our torque wrenches are calibrated every six months.
kunci sok, kunci shock
a wrench with a handle and interchangeable round sockets that fit over nuts and bolt heads
A socket wrench is faster than a spanner in tight spaces.
Kunci sok lebih cepat daripada kunci pas di ruang yang sempit.
The technician keeps a full socket wrench set in his toolbox.
kunci L, kunci inbus
a small L-shaped metal bar with six flat sides, used to turn screws with a hexagonal hole
You need a 5 mm Allen key to remove the guard cover.
Anda memerlukan kunci L 5 mm untuk melepas penutup pelindung.
Do not use a worn Allen key, or you will damage the screw head.
gergaji besi, gergaji tangan besi
a hand saw with a thin, fine-toothed blade in a frame, used for cutting metal
Cut the pipe to length with a hacksaw and then file the end.
Potong pipa sesuai panjang dengan gergaji besi, lalu haluskan ujungnya dengan kikir.
Change the hacksaw blade when the teeth become dull.
kikir
a steel hand tool with a rough surface, used for smoothing or shaping metal by rubbing
Use a flat file to remove the sharp edges after cutting.
Gunakan kikir datar untuk menghilangkan tepi yang tajam setelah pemotongan.
Apprentices practise with a file before they move on to the lathe.
ragum, ragum meja
a tool fixed to a workbench with two jaws that hold a piece of work firmly while you work on it
Clamp the bar in the bench vice before you start sawing.
Jepit batang itu di ragum sebelum mulai menggergaji.
Use soft jaws in the bench vice to protect the finished surface.
penitik, penitik pusat
a pointed steel tool hit with a hammer to make a small mark where a hole will be drilled
Mark each hole position with a centre punch so the drill does not wander.
Tandai setiap posisi lubang dengan penitik agar mata bor tidak meleset.
An automatic centre punch makes marking faster on thin sheet.
bor listrik, mesin bor tangan
a hand-held electric tool that turns a drill bit to make holes
A cordless power drill is handy for installing brackets on site.
Bor listrik tanpa kabel sangat praktis untuk memasang braket di lokasi kerja.
Check the power drill cable for damage before every use.
gerinda tangan, gerinda sudut
a hand-held power tool with a fast spinning disc, used for cutting, grinding and polishing metal
Never remove the guard from an angle grinder.
Jangan pernah melepas pelindung dari gerinda tangan.
He cleaned the weld with an angle grinder and a flap disc.
kunci impak, wrench impak
a power tool that gives strong, fast turning blows to tighten or loosen large nuts and bolts
The mechanic used an impact wrench to remove the wheel nuts.
Mekanik itu menggunakan kunci impak untuk melepas mur roda.
Do not use an impact wrench for final tightening; use a torque wrench.



