Langsung ke konten

Pelajaran 7/10 · 16 kata · 0 sudah hafal

Control systems and automation

Sistem kendali dan otomasi

  1. 1

    sensor(noun)

    /ˈsensər/

    sensor

    a device that detects a physical condition such as temperature, pressure or position and sends a signal

    A faulty temperature sensor made the chiller shut down.

    Sensor suhu yang rusak membuat chiller mati.

    Wire the pressure sensor to the analogue input of the controller.

    Sinonimdetectortransducermonitorgaugeprobe
    Antonimnone
  2. 2

    contactor(noun)

    /'kɔntæktə/

    kontaktor

    a heavy-duty relay used to switch power circuits, such as motors, on and off

    The contactor pulls in when the start button is pressed.

    Kontaktor menarik (menutup) saat tombol start ditekan.

    Worn contactor tips can cause a motor to run on two phases.

    Sinonimrelayswitchcircuit breaker
    Antoniminsulatoropen circuit
  3. 3

    control panel(noun)

    /kənˈtrəʊl ˈpænl/

    panel kontrol, panel kendali

    an enclosure containing the controls, relays, PLC and indicators that operate a machine or process

    Keep the control panel door closed to stop dust getting in.

    Tutup selalu pintu panel kontrol agar debu tidak masuk.

    The control panel was built and tested at our workshop before delivery.

    Sinonimdashboardinterfaceconsolesettingscommand center
    Antonim(in this contextantonyms are not very applicablebut perhaps) chaosdisorderuncontrolled
  4. 4

    solenoid valve(noun)

    /ˈsəʊlənɔɪd vælv/

    katup solenoid, katup selenoid

    a valve opened and closed by an electric coil, so it can be controlled automatically

    The PLC switches the solenoid valve to start the air blast.

    PLC mengaktifkan katup solenoid untuk memulai semburan udara.

    The solenoid valve coil burned out and the cylinder stopped.

  5. 5

    actuator(noun)

    /ˈæktʃueɪtə(r)/

    aktuator, penggerak

    a part such as a cylinder or motor that turns energy into movement to operate a machine

    A pneumatic actuator opens the gate on the hopper.

    Aktuator pneumatik membuka pintu pada hopper.

    Check the actuator stroke after replacing the seals.

  6. 6

    PLC(abbreviation)

    /ˌpiː el ˈsiː/

    PLC, pengendali logika terprogram

    programmable logic controller: an industrial controller that reads inputs from sensors and switches outputs to run machines

    The PLC stops the conveyor when the photo sensor detects a jam.

    PLC menghentikan konveyor saat sensor foto mendeteksi kemacetan.

    Check the PLC input lights to see which limit switch is active.

  7. 7

    HMI(abbreviation)

    /ˌeɪtʃ em ˈaɪ/

    HMI, antarmuka manusia-mesin

    human-machine interface: a touch screen or panel that lets operators see machine status and change settings

    The operator reset the alarm from the HMI screen.

    Operator mengatur ulang alarm dari layar HMI.

    Add a page on the HMI to show the motor running hours.

  8. 8

    SCADA(abbreviation)

    /ˈskɑːdə/

    SCADA, sistem kendali supervisori dan akuisisi data

    supervisory control and data acquisition: a system that monitors and controls equipment across a whole plant or network from a central room

    The water company monitors all its pumping stations through SCADA.

    Perusahaan air itu memantau semua stasiun pompanya melalui SCADA.

    The SCADA system logged the exact time the breaker tripped.

  9. 9

    proximity sensor(noun)

    /prɒkˈsɪməti ˌsensə(r)/

    sensor proximitas, sensor jarak dekat

    a sensor that detects a nearby object without touching it, often used to detect metal parts

    An inductive proximity sensor counts the bolts on the conveyor.

    Sensor proximitas induktif menghitung baut yang ada di konveyor.

    Set the proximity sensor about three millimetres from the target.

  10. 10

    limit switch(noun)

    /ˈlɪmɪt swɪtʃ/

    saklar batas, limit switch

    a switch operated by a moving part of a machine, used to detect its end position

    The door stops when it presses the upper limit switch.

    Pintu berhenti ketika menekan saklar batas atas.

    Replace the limit switch if the roller arm is bent.

  11. 11

    relay(noun)

    /ˈriːleɪ/

    relai

    an electrically operated switch in which a small current through a coil switches a separate circuit

    The PLC output drives a relay that switches the alarm horn.

    Keluaran PLC menggerakkan relai yang mengalihkan klakson alarm.

    The relay contacts were burnt, so the heater would not switch off.

  12. 12

    interlock(noun)

    /ˈɪntəlɒk/

    interlock, sistem pengunci pengaman

    a control arrangement that stops a machine or action unless certain safe conditions are met

    The door interlock stops the machine as soon as the guard is opened.

    Interlock pintu menghentikan mesin begitu pelindung dibuka.

    Never bypass a safety interlock to keep production running.

  13. 13

    push button(noun)

    /ˈpʊʃ ˌbʌtn/

    tombol tekan

    a button on a control panel that is pressed to start, stop or reset equipment

    Press the green push button to start the pump.

    Tekan tombol tekan hijau untuk menyalakan pompa.

    The stop push button has a normally closed contact.

  14. 14

    pilot light(noun)

    /ˈpaɪlət laɪt/

    lampu indikator, lampu pilot

    a small indicator lamp on a panel that shows whether equipment is running, stopped or in fault

    The red pilot light shows that the motor has tripped.

    Lampu indikator merah menunjukkan bahwa motor telah trip.

    Replace the pilot light bulb if it does not come on during the lamp test.

  15. 15

    setpoint(noun)

    /ˈsetpɔɪnt/

    titik setel, nilai setel

    the target value, such as a temperature or pressure, that a control system tries to maintain

    Raise the pressure setpoint to 5 bar on the controller.

    Naikkan titik setel tekanan menjadi 5 bar pada pengendali.

    The room stayed warm because the setpoint was entered wrongly.

  16. 16

    encoder(noun)

    /ɪnˈkəʊdə(r)/

    enkoder, encoder

    a sensor fixed to a shaft that sends pulses showing its position, speed or direction

    The encoder on the motor shaft gives speed feedback to the drive.

    Enkoder pada poros motor memberikan umpan balik kecepatan ke drive.

    A loose encoder cable caused the axis to lose its position.