Skip to content

Lesson 7/10 · 16 words · 0 learned

Control systems and automation

  1. 1

    sensor(noun)

    /ˈsensər/

    a device that detects a physical condition such as temperature, pressure or position and sends a signal

    A faulty temperature sensor made the chiller shut down.

    Wire the pressure sensor to the analogue input of the controller.

    Synonymsdetectortransducermonitorgaugeprobe
    Antonymsnone
  2. 2

    contactor(noun)

    /'kɔntæktə/

    a heavy-duty relay used to switch power circuits, such as motors, on and off

    The contactor pulls in when the start button is pressed.

    Worn contactor tips can cause a motor to run on two phases.

    Synonymsrelayswitchcircuit breaker
    Antonymsinsulatoropen circuit
  3. 3

    control panel(noun)

    /kənˈtrəʊl ˈpænl/

    an enclosure containing the controls, relays, PLC and indicators that operate a machine or process

    Keep the control panel door closed to stop dust getting in.

    The control panel was built and tested at our workshop before delivery.

    Synonymsdashboardinterfaceconsolesettingscommand center
    Antonyms(in this contextantonyms are not very applicablebut perhaps) chaosdisorderuncontrolled
  4. 4

    solenoid valve(noun)

    /ˈsəʊlənɔɪd vælv/

    a valve opened and closed by an electric coil, so it can be controlled automatically

    The PLC switches the solenoid valve to start the air blast.

    The solenoid valve coil burned out and the cylinder stopped.

  5. 5

    actuator(noun)

    /ˈæktʃueɪtə(r)/

    a part such as a cylinder or motor that turns energy into movement to operate a machine

    A pneumatic actuator opens the gate on the hopper.

    Check the actuator stroke after replacing the seals.

  6. 6

    PLC(abbreviation)

    /ˌpiː el ˈsiː/

    programmable logic controller: an industrial controller that reads inputs from sensors and switches outputs to run machines

    The PLC stops the conveyor when the photo sensor detects a jam.

    Check the PLC input lights to see which limit switch is active.

  7. 7

    HMI(abbreviation)

    /ˌeɪtʃ em ˈaɪ/

    human-machine interface: a touch screen or panel that lets operators see machine status and change settings

    The operator reset the alarm from the HMI screen.

    Add a page on the HMI to show the motor running hours.

  8. 8

    SCADA(abbreviation)

    /ˈskɑːdə/

    supervisory control and data acquisition: a system that monitors and controls equipment across a whole plant or network from a central room

    The water company monitors all its pumping stations through SCADA.

    The SCADA system logged the exact time the breaker tripped.

  9. 9

    proximity sensor(noun)

    /prɒkˈsɪməti ˌsensə(r)/

    a sensor that detects a nearby object without touching it, often used to detect metal parts

    An inductive proximity sensor counts the bolts on the conveyor.

    Set the proximity sensor about three millimetres from the target.

  10. 10

    limit switch(noun)

    /ˈlɪmɪt swɪtʃ/

    a switch operated by a moving part of a machine, used to detect its end position

    The door stops when it presses the upper limit switch.

    Replace the limit switch if the roller arm is bent.

  11. 11

    relay(noun)

    /ˈriːleɪ/

    an electrically operated switch in which a small current through a coil switches a separate circuit

    The PLC output drives a relay that switches the alarm horn.

    The relay contacts were burnt, so the heater would not switch off.

  12. 12

    interlock(noun)

    /ˈɪntəlɒk/

    a control arrangement that stops a machine or action unless certain safe conditions are met

    The door interlock stops the machine as soon as the guard is opened.

    Never bypass a safety interlock to keep production running.

  13. 13

    push button(noun)

    /ˈpʊʃ ˌbʌtn/

    a button on a control panel that is pressed to start, stop or reset equipment

    Press the green push button to start the pump.

    The stop push button has a normally closed contact.

  14. 14

    pilot light(noun)

    /ˈpaɪlət laɪt/

    a small indicator lamp on a panel that shows whether equipment is running, stopped or in fault

    The red pilot light shows that the motor has tripped.

    Replace the pilot light bulb if it does not come on during the lamp test.

  15. 15

    setpoint(noun)

    /ˈsetpɔɪnt/

    the target value, such as a temperature or pressure, that a control system tries to maintain

    Raise the pressure setpoint to 5 bar on the controller.

    The room stayed warm because the setpoint was entered wrongly.

  16. 16

    encoder(noun)

    /ɪnˈkəʊdə(r)/

    a sensor fixed to a shaft that sends pulses showing its position, speed or direction

    The encoder on the motor shaft gives speed feedback to the drive.

    A loose encoder cable caused the axis to lose its position.