Langkau ke kandungan

Pelajaran 7/10 · 16 perkataan · 0 sudah dipelajari

Control systems and automation

Sistem kawalan dan automasi

  1. 1

    sensor(noun)

    /ˈsensər/

    penderia, sensor

    a device that detects a physical condition such as temperature, pressure or position and sends a signal

    A faulty temperature sensor made the chiller shut down.

    Penderia suhu yang rosak menyebabkan pendingin itu berhenti beroperasi.

    Wire the pressure sensor to the analogue input of the controller.

    Sinonimdetectortransducermonitorgaugeprobe
    Antonimnone
  2. 2

    contactor(noun)

    /'kɔntæktə/

    kontaktor

    a heavy-duty relay used to switch power circuits, such as motors, on and off

    The contactor pulls in when the start button is pressed.

    Kontaktor akan tertarik apabila butang mula ditekan.

    Worn contactor tips can cause a motor to run on two phases.

    Sinonimrelayswitchcircuit breaker
    Antoniminsulatoropen circuit
  3. 3

    control panel(noun)

    /kənˈtrəʊl ˈpænl/

    panel kawalan

    an enclosure containing the controls, relays, PLC and indicators that operate a machine or process

    Keep the control panel door closed to stop dust getting in.

    Pastikan pintu panel kawalan sentiasa tertutup supaya habuk tidak masuk.

    The control panel was built and tested at our workshop before delivery.

    Sinonimdashboardinterfaceconsolesettingscommand center
    Antonim(in this contextantonyms are not very applicablebut perhaps) chaosdisorderuncontrolled
  4. 4

    solenoid valve(noun)

    /ˈsəʊlənɔɪd vælv/

    injap solenoid

    a valve opened and closed by an electric coil, so it can be controlled automatically

    The PLC switches the solenoid valve to start the air blast.

    PLC menukar injap solenoid untuk memulakan tiupan udara.

    The solenoid valve coil burned out and the cylinder stopped.

  5. 5

    actuator(noun)

    /ˈæktʃueɪtə(r)/

    penggerak, aktuator

    a part such as a cylinder or motor that turns energy into movement to operate a machine

    A pneumatic actuator opens the gate on the hopper.

    Penggerak pneumatik membuka pintu pada hopper.

    Check the actuator stroke after replacing the seals.

  6. 6

    PLC(abbreviation)

    /ˌpiː el ˈsiː/

    PLC, pengawal logik boleh atur cara

    programmable logic controller: an industrial controller that reads inputs from sensors and switches outputs to run machines

    The PLC stops the conveyor when the photo sensor detects a jam.

    PLC menghentikan penghantar apabila penderia foto mengesan kesesakan.

    Check the PLC input lights to see which limit switch is active.

  7. 7

    HMI(abbreviation)

    /ˌeɪtʃ em ˈaɪ/

    HMI, antara muka manusia-mesin

    human-machine interface: a touch screen or panel that lets operators see machine status and change settings

    The operator reset the alarm from the HMI screen.

    Operator menetapkan semula penggera daripada skrin HMI.

    Add a page on the HMI to show the motor running hours.

  8. 8

    SCADA(abbreviation)

    /ˈskɑːdə/

    SCADA, kawalan penyeliaan dan perolehan data

    supervisory control and data acquisition: a system that monitors and controls equipment across a whole plant or network from a central room

    The water company monitors all its pumping stations through SCADA.

    Syarikat air itu memantau semua stesen pamnya melalui SCADA.

    The SCADA system logged the exact time the breaker tripped.

  9. 9

    proximity sensor(noun)

    /prɒkˈsɪməti ˌsensə(r)/

    penderia hampiran, sensor hampiran

    a sensor that detects a nearby object without touching it, often used to detect metal parts

    An inductive proximity sensor counts the bolts on the conveyor.

    Penderia hampiran induktif mengira bolt pada penghantar.

    Set the proximity sensor about three millimetres from the target.

  10. 10

    limit switch(noun)

    /ˈlɪmɪt swɪtʃ/

    suis had, suis penghad

    a switch operated by a moving part of a machine, used to detect its end position

    The door stops when it presses the upper limit switch.

    Pintu berhenti apabila menekan suis had atas.

    Replace the limit switch if the roller arm is bent.

  11. 11

    relay(noun)

    /ˈriːleɪ/

    geganti

    an electrically operated switch in which a small current through a coil switches a separate circuit

    The PLC output drives a relay that switches the alarm horn.

    Keluaran PLC menggerakkan geganti yang menyuis hon penggera.

    The relay contacts were burnt, so the heater would not switch off.

  12. 12

    interlock(noun)

    /ˈɪntəlɒk/

    saling kunci, interlok

    a control arrangement that stops a machine or action unless certain safe conditions are met

    The door interlock stops the machine as soon as the guard is opened.

    Saling kunci pintu menghentikan mesin sebaik sahaja pengadang dibuka.

    Never bypass a safety interlock to keep production running.

  13. 13

    push button(noun)

    /ˈpʊʃ ˌbʌtn/

    butang tekan

    a button on a control panel that is pressed to start, stop or reset equipment

    Press the green push button to start the pump.

    Tekan butang tekan hijau untuk menghidupkan pam.

    The stop push button has a normally closed contact.

  14. 14

    pilot light(noun)

    /ˈpaɪlət laɪt/

    lampu penunjuk

    a small indicator lamp on a panel that shows whether equipment is running, stopped or in fault

    The red pilot light shows that the motor has tripped.

    Lampu penunjuk merah menunjukkan motor telah trip.

    Replace the pilot light bulb if it does not come on during the lamp test.

  15. 15

    setpoint(noun)

    /ˈsetpɔɪnt/

    titik set, nilai tetapan

    the target value, such as a temperature or pressure, that a control system tries to maintain

    Raise the pressure setpoint to 5 bar on the controller.

    Naikkan titik set tekanan kepada 5 bar pada pengawal.

    The room stayed warm because the setpoint was entered wrongly.

  16. 16

    encoder(noun)

    /ɪnˈkəʊdə(r)/

    pengekod, pengekod putaran

    a sensor fixed to a shaft that sends pulses showing its position, speed or direction

    The encoder on the motor shaft gives speed feedback to the drive.

    Pengekod pada aci motor memberikan maklum balas kelajuan kepada pemacu.

    A loose encoder cable caused the axis to lose its position.