Lumaktaw sa nilalaman

Aralin 7/10 · 16 salita · 0 natutunan

Control systems and automation

Mga control system at awtomasyon

  1. 1

    sensor(noun)

    /ˈsensər/

    sensor, pandama

    a device that detects a physical condition such as temperature, pressure or position and sends a signal

    A faulty temperature sensor made the chiller shut down.

    Ang sirang sensor ng temperatura ang nagpasara sa chiller.

    Wire the pressure sensor to the analogue input of the controller.

    Kasingkahulugandetectortransducermonitorgaugeprobe
    Kasalungatnone
  2. 2

    contactor(noun)

    /'kɔntæktə/

    kontaktor, magnetikong kontaktor

    a heavy-duty relay used to switch power circuits, such as motors, on and off

    The contactor pulls in when the start button is pressed.

    Kumakapit ang kontaktor kapag pinindot ang start button.

    Worn contactor tips can cause a motor to run on two phases.

    Kasingkahuluganrelayswitchcircuit breaker
    Kasalungatinsulatoropen circuit
  3. 3

    control panel(noun)

    /kənˈtrəʊl ˈpænl/

    panel ng kontrol, kabinet ng kontrol

    an enclosure containing the controls, relays, PLC and indicators that operate a machine or process

    Keep the control panel door closed to stop dust getting in.

    Panatilihing nakasara ang pinto ng panel ng kontrol upang hindi makapasok ang alikabok.

    The control panel was built and tested at our workshop before delivery.

    Kasingkahulugandashboardinterfaceconsolesettingscommand center
    Kasalungat(in this contextantonyms are not very applicablebut perhaps) chaosdisorderuncontrolled
  4. 4

    solenoid valve(noun)

    /ˈsəʊlənɔɪd vælv/

    balbulang solenoid, balbulang de-kuryente

    a valve opened and closed by an electric coil, so it can be controlled automatically

    The PLC switches the solenoid valve to start the air blast.

    Binubuksan ng PLC ang balbulang solenoid upang simulan ang pagbuga ng hangin.

    The solenoid valve coil burned out and the cylinder stopped.

  5. 5

    actuator(noun)

    /ˈæktʃueɪtə(r)/

    aktuwetor, mekanismong pampagalaw

    a part such as a cylinder or motor that turns energy into movement to operate a machine

    A pneumatic actuator opens the gate on the hopper.

    Isang aktuwetor na niyumatiko ang nagbubukas ng pinto ng hopper.

    Check the actuator stroke after replacing the seals.

  6. 6

    PLC(abbreviation)

    /ˌpiː el ˈsiː/

    PLC, programmable na kontroler na lohika

    programmable logic controller: an industrial controller that reads inputs from sensors and switches outputs to run machines

    The PLC stops the conveyor when the photo sensor detects a jam.

    Pinapatigil ng PLC ang conveyor kapag natukoy ng photo sensor ang pagbara.

    Check the PLC input lights to see which limit switch is active.

  7. 7

    HMI(abbreviation)

    /ˌeɪtʃ em ˈaɪ/

    HMI, interface ng tao at makina

    human-machine interface: a touch screen or panel that lets operators see machine status and change settings

    The operator reset the alarm from the HMI screen.

    Ni-reset ng operator ang alarma mula sa HMI screen.

    Add a page on the HMI to show the motor running hours.

  8. 8

    SCADA(abbreviation)

    /ˈskɑːdə/

    SCADA, sistema ng pagsubaybay at pagkolekta ng datos

    supervisory control and data acquisition: a system that monitors and controls equipment across a whole plant or network from a central room

    The water company monitors all its pumping stations through SCADA.

    Sinusubaybayan ng kompanya ng tubig ang lahat ng pumping station nito sa pamamagitan ng SCADA.

    The SCADA system logged the exact time the breaker tripped.

  9. 9

    proximity sensor(noun)

    /prɒkˈsɪməti ˌsensə(r)/

    sensor ng kalapitan

    a sensor that detects a nearby object without touching it, often used to detect metal parts

    An inductive proximity sensor counts the bolts on the conveyor.

    Binibilang ng inductive na sensor ng kalapitan ang mga bolt sa conveyor.

    Set the proximity sensor about three millimetres from the target.

  10. 10

    limit switch(noun)

    /ˈlɪmɪt swɪtʃ/

    suwits pangwakas ng takbo

    a switch operated by a moving part of a machine, used to detect its end position

    The door stops when it presses the upper limit switch.

    Humihinto ang pinto kapag napindot nito ang itaas na suwits pangwakas ng takbo.

    Replace the limit switch if the roller arm is bent.

  11. 11

    relay(noun)

    /ˈriːleɪ/

    relé

    an electrically operated switch in which a small current through a coil switches a separate circuit

    The PLC output drives a relay that switches the alarm horn.

    Ang output ng PLC ay nagpapagana ng relé na nagpapaandar sa busina ng alarma.

    The relay contacts were burnt, so the heater would not switch off.

  12. 12

    interlock(noun)

    /ˈɪntəlɒk/

    interlok, kandadong pangkaligtasan

    a control arrangement that stops a machine or action unless certain safe conditions are met

    The door interlock stops the machine as soon as the guard is opened.

    Pinahihinto ng interlok ng pinto ang makina sa sandaling mabuksan ang guard.

    Never bypass a safety interlock to keep production running.

  13. 13

    push button(noun)

    /ˈpʊʃ ˌbʌtn/

    pindutan

    a button on a control panel that is pressed to start, stop or reset equipment

    Press the green push button to start the pump.

    Pindutin ang berdeng pindutan para paandarin ang bomba.

    The stop push button has a normally closed contact.

  14. 14

    pilot light(noun)

    /ˈpaɪlət laɪt/

    ilaw pananda, ilaw pang-indikasyon

    a small indicator lamp on a panel that shows whether equipment is running, stopped or in fault

    The red pilot light shows that the motor has tripped.

    Ipinapakita ng pulang ilaw pananda na nag-trip ang motor.

    Replace the pilot light bulb if it does not come on during the lamp test.

  15. 15

    setpoint(noun)

    /ˈsetpɔɪnt/

    itinakdang halaga, target na halaga

    the target value, such as a temperature or pressure, that a control system tries to maintain

    Raise the pressure setpoint to 5 bar on the controller.

    Itaas sa 5 bar ang itinakdang halaga ng presyon sa controller.

    The room stayed warm because the setpoint was entered wrongly.

  16. 16

    encoder(noun)

    /ɪnˈkəʊdə(r)/

    enkoder

    a sensor fixed to a shaft that sends pulses showing its position, speed or direction

    The encoder on the motor shaft gives speed feedback to the drive.

    Ang enkoder sa baras ng motor ay nagbibigay ng feedback ng bilis sa drive.

    A loose encoder cable caused the axis to lose its position.