सामग्री पर जाएँ

पाठ 10/10 · 16 शब्द · 0 याद हो गए

Maintenance and troubleshooting

रखरखाव और समस्या निवारण

  1. 1

    breakdown(noun)

    /ˈbreɪkdaʊn/

    ब्रेकडाउन, खराबी

    a sudden failure of a machine or vehicle so that it stops working

    A breakdown of the main compressor stopped the whole line.

    मुख्य कंप्रेसर के ब्रेकडाउन से पूरी लाइन रुक गई।

    Report every breakdown in the maintenance system with the cause.

    समानार्थीfailuremalfunctioncollapserupturedeterioration
    विलोमrepairfiximprovementconstructionstability
  2. 2

    downtime(noun)

    /ˈdaʊntaɪm/

    डाउनटाइम, बंद रहने का समय

    the time during which a computer system or machine is not working or not available

    Every hour of downtime costs the online shop thousands of dollars.

    डाउनटाइम का हर घंटा ऑनलाइन दुकान को हज़ारों डॉलर का नुकसान पहुँचाता है।

    The upgrade will cause about thirty minutes of downtime.

    समानार्थीidle timestandstillinactivitynon-operational period
    विलोमuptimeoperationactivity
  3. 3

    lubrication(noun)

    /ˌluːbrɪˈkeɪʃn/

    स्नेहन, चिकनाई देना

    putting oil or grease on moving parts to reduce friction, wear and heat

    Poor lubrication is the most common cause of bearing failure.

    खराब स्नेहन बेयरिंग के विफल होने का सबसे आम कारण है।

    Each machine has a lubrication chart showing every grease point.

    समानार्थीgreasingoilingslickingcoating
    विलोमfrictionabrasiongrinding
  4. 4

    overhaul(noun)

    /ˈəʊvərhɔːl/

    ओवरहॉल, पूर्ण मरम्मत

    a complete check of a machine in which it is taken apart, repaired and put back together

    The compressor is due for a major overhaul after 40,000 hours.

    40,000 घंटे के बाद कंप्रेसर का बड़ा ओवरहॉल होना है।

    A full overhaul of the press will take ten working days.

    समानार्थीrenovatereconditionrebuildreconstruct
    विलोमneglectignoremaintain
  5. 5

    troubleshoot(verb)

    /ˈtrʌblʃuːt/

    समस्या निवारण करना, ट्रबलशूट करना

    to find the cause of a technical problem and fix it, usually by checking possible causes one by one

    The technician spent an hour troubleshooting the Wi-Fi in the meeting room.

    तकनीशियन ने मीटिंग रूम के वाई-फ़ाई की समस्या का निवारण करने में एक घंटा लगाया।

    Follow these steps to troubleshoot common login problems.

    समानार्थीdiagnosefixresolvedebug
    विलोमignoreneglect
  6. 6

    spare part(noun)

    /sper pɑːrt/

    अतिरिक्त पुर्ज़ा, स्पेयर पार्ट

    a part kept in stock to replace one that breaks or wears out

    Keep critical spare parts such as seals and belts in the store.

    सील और बेल्ट जैसे महत्वपूर्ण अतिरिक्त पुर्ज़े स्टोर में रखें।

    The machine was down for a week waiting for a spare part.

    समानार्थीreplacement partcomponentaccessory
    विलोमprimary partoriginal component
  7. 7

    work order(noun)

    /ˈwɜːk ˌɔːdə(r)/

    कार्य आदेश, मरम्मत अनुरोध

    a written or electronic request to the engineering department to repair something

    Reception created a work order for the broken shower in room 211.

    रिसेप्शन ने कमरा 211 के टूटे शॉवर के लिए कार्य आदेश बनाया।

    Urgent work orders must be completed within one hour.

  8. 8

    preventive maintenance(noun)

    /prɪˌventɪv ˈmeɪntənəns/

    निवारक रखरखाव, निवारक अनुरक्षण

    regular planned servicing of machines, such as cleaning and replacing parts, to stop them breaking down

    Preventive maintenance on the presses is done every Saturday.

    प्रेसों का निवारक रखरखाव हर शनिवार को किया जाता है।

    Good preventive maintenance has cut our breakdowns by half.

  9. 9

    predictive maintenance(noun)

    /prɪˌdɪktɪv ˈmeɪntənəns/

    पूर्वानुमानित रखरखाव, भविष्यसूचक रखरखाव

    maintenance based on monitoring the condition of a machine, so parts are replaced just before they fail

    Predictive maintenance uses vibration and temperature data to plan repairs.

    पूर्वानुमानित रखरखाव में मरम्मत की योजना बनाने के लिए कंपन और तापमान के आँकड़ों का उपयोग किया जाता है।

    Sensors on the motors support our predictive maintenance programme.

  10. 10

    corrective maintenance(noun)

    /kəˌrektɪv ˈmeɪntənəns/

    सुधारात्मक रखरखाव, उपचारात्मक रखरखाव

    repair work done after a fault has been found, to bring a machine back to normal operation

    Most of our corrective maintenance is caused by worn belts.

    हमारे अधिकांश सुधारात्मक रखरखाव का कारण घिसी हुई बेल्टें हैं।

    Corrective maintenance costs more than planned work because of lost production.

  11. 11

    wear(noun)

    /weə(r)/

    घिसाव, घिसावट

    damage or loss of material on a surface caused by rubbing and use over time

    Check the guide rails for wear every month.

    हर महीने गाइड रेलों में घिसाव की जाँच करें।

    The chain has reached its wear limit and must be replaced.

  12. 12

    misalignment(noun)

    /ˌmɪsəˈlaɪnmənt/

    असंरेखण, संरेखण त्रुटि

    the condition when two connected shafts or parts are not in a straight line as they should be

    Misalignment between the motor and pump caused the coupling to fail.

    मोटर और पंप के बीच असंरेखण के कारण कपलिंग विफल हो गई।

    We use a laser tool to correct shaft misalignment.

  13. 13

    vibration analysis(noun)

    /vaɪˈbreɪʃn ənæləsɪs/

    कंपन विश्लेषण

    measuring and studying the vibration of a machine to find problems such as worn bearings or imbalance

    Vibration analysis showed an outer race defect in the fan bearing.

    कंपन विश्लेषण से पंखे के बेयरिंग के बाहरी रेस में दोष का पता चला।

    An outside company does vibration analysis on our pumps every quarter.

  14. 14

    root cause analysis(noun)

    /ˌruːt ˈkɔːz ənæləsɪs/

    मूल कारण विश्लेषण

    a step-by-step method to find the real basic reason for a failure so it does not happen again

    We did a root cause analysis after the third gearbox failure.

    तीसरी बार गियरबॉक्स विफल होने के बाद हमने मूल कारण विश्लेषण किया।

    Root cause analysis showed that the wrong oil had been used.

  15. 15

    MTBF(abbreviation)

    /ˌem tiː biː ˈef/

    MTBF, विफलताओं के बीच औसत समय

    mean time between failures: the average running time of a machine between one breakdown and the next

    Our target is to raise the MTBF of the packing line to 200 hours.

    हमारा लक्ष्य पैकिंग लाइन का MTBF बढ़ाकर 200 घंटे करना है।

    MTBF improved after we changed the lubrication schedule.

  16. 16

    backlash(noun)

    /ˈbæklæʃ/

    दंत-अंतराल, बैकलैश

    the small amount of free movement between meshing parts, such as gear teeth, before they engage

    Too much backlash in the gearbox causes poor positioning accuracy.

    गियरबॉक्स में बहुत अधिक दंत-अंतराल होने से स्थिति-निर्धारण की सटीकता खराब हो जाती है।

    Measure the backlash with a dial indicator after fitting the new gear.