Langsung ke konten

Pelajaran 6/10 · 17 kata · 0 sudah hafal

Machine elements

Elemen mesin

  1. 1

    gasket(noun)

    /ˈɡæskɪt/

    paking, gasket

    a flat piece of soft material placed between two joined surfaces to stop gas or liquid leaking

    Always fit a new gasket when you reassemble the pump cover.

    Selalu pasang paking baru saat Anda memasang kembali penutup pompa.

    Oil was leaking because the gasket was damaged.

    Sinonimsealwasherpacking
    Antonimnone
  2. 2

    pulley(noun)

    /ˈpʊli/

    puli, katrol

    a wheel with a groove around it that carries a belt or rope to transmit power or lift loads

    Replace both pulleys if their grooves are badly worn.

    Ganti kedua puli jika alurnya sudah sangat aus.

    The motor pulley is smaller to reduce the fan speed.

    Sinonimblocksheavewinch
    AntonimNone
  3. 3

    rivet(noun)

    /ˈrɪvɪt/

    paku keling, rivet

    a short metal pin used to join metal sheets permanently by hammering or pressing its end flat

    The panels are joined with aluminium blind rivets.

    Panel-panel itu disambung dengan paku keling buta dari aluminium.

    Drill out the old rivet before fitting the new bracket.

    Sinonimfastenerboltpin
    Antonimweldadhesive
  4. 4

    spur gear(noun)

    /spɜːr ɡɪr/

    roda gigi lurus, gigi lurus

    the simplest type of gear, with straight teeth parallel to the shaft

    Spur gears are cheap to make but noisier than helical gears.

    Roda gigi lurus murah untuk dibuat tetapi lebih berisik daripada roda gigi helikal.

    The feeder uses a pair of spur gears to reduce speed.

    Sinonimstraight-cut gear
    Antonimhelical gearbevel gear
  5. 5

    washer(noun)

    /ˈwɑːʃər/

    ring, cincin pengunci, washer

    a thin flat ring placed under a nut or bolt head to spread the load or stop it loosening

    Put a flat washer under each nut to protect the painted surface.

    Pasang ring plat di bawah setiap mur untuk melindungi permukaan yang dicat.

    Spring washers stop the bolts loosening from vibration.

    Sinonimshimspacer
    Antonimnone
  6. 6

    belt drive(noun)

    /belt draɪv/

    transmisi sabuk, penggerak sabuk

    a system that uses a belt running over pulleys to pass power from one shaft to another

    Check the belt drive tension after the first 24 hours of running.

    Periksa ketegangan transmisi sabuk setelah 24 jam pertama beroperasi.

    A belt drive is quieter and cheaper than a chain drive.

    Sinonimbelt transmissionbelt power transfer
    Antonimdirect drivegear drive
  7. 7

    gearbox(noun)

    /ˈɡɪrbɑːks/

    gearbox, kotak roda gigi, reduktor

    a closed housing containing a set of gears that changes the speed and turning force between a motor and a machine

    The conveyor motor is fitted with a 20 to 1 reduction gearbox.

    Motor konveyor dilengkapi gearbox reduksi dengan rasio 20 banding 1.

    Check the gearbox oil level during the weekly inspection.

    Sinonimtransmissiongear case
    AntonimNone
  8. 8

    shaft(noun)

    /ʃɑːft/

    poros

    a long round bar in a machine that turns and carries power from one part to another

    The motor drives the pump through a short steel shaft.

    Motor menggerakkan pompa melalui poros baja yang pendek.

    A bent shaft was causing the vibration in the fan.

  9. 9

    bearing(noun)

    /ˈbeərɪŋ/

    bantalan, bearing

    a machine part that supports a turning shaft and reduces friction between moving parts

    The noise is coming from a worn bearing in the gearbox.

    Suara bising berasal dari bantalan yang aus di dalam kotak roda gigi.

    Grease the conveyor bearings every 500 operating hours.

  10. 10

    ball bearing(noun)

    /ˌbɔːl ˈbeərɪŋ/

    bantalan bola, bearing bola

    a bearing in which small steel balls roll between an inner and an outer ring

    The motor uses two sealed ball bearings that need no extra grease.

    Motor ini menggunakan dua bantalan bola tertutup yang tidak memerlukan gemuk tambahan.

    Order a 6205 deep groove ball bearing as a spare.

  11. 11

    roller bearing(noun)

    /ˌrəʊlə ˈbeərɪŋ/

    bantalan rol, bearing rol

    a bearing that uses cylinders or tapered rollers instead of balls, so it can carry heavier loads

    The wheel hub runs on two tapered roller bearings.

    Hub roda berputar pada dua bantalan rol kerucut.

    We chose a roller bearing because the radial load is very high.

  12. 12

    gear(noun)

    /ɡɪə(r)/

    roda gigi, gir

    a wheel with teeth around its edge that fits with another toothed wheel to pass on movement and power

    Two teeth on the drive gear were broken.

    Dua gigi pada roda gigi penggerak patah.

    Changing the gear ratio will increase the output torque.

  13. 13

    coupling(noun)

    /ˈkʌplɪŋ/

    kopling, kopling poros

    a device that joins the ends of two shafts so that power passes from one to the other

    A flexible coupling connects the motor to the pump shaft.

    Kopling fleksibel menghubungkan motor ke poros pompa.

    The rubber insert in the coupling had worn out.

  14. 14

    keyway(noun)

    /ˈkiːweɪ/

    alur pasak

    a slot cut in a shaft or hub where a key fits, so that the two turn together

    The keyway is milled after the shaft is turned to size.

    Alur pasak difrais setelah poros dibubut sesuai ukuran.

    A worn keyway lets the pulley slip on the shaft.

  15. 15

    bolt(noun)

    /bəʊlt/

    baut

    a metal rod with a head and a screw thread, used with a nut to hold parts together

    Use grade 8.8 bolts for the motor base.

    Gunakan baut kelas 8.8 untuk dudukan motor.

    Two bolts on the guard were missing after maintenance.

  16. 16

    O-ring(noun)

    /ˈəʊ rɪŋ/

    O-ring, cincin-O, seal cincin-O

    a rubber ring with a round cross-section that sits in a groove to seal a joint

    Lightly oil the O-ring before you push the fitting in.

    Lumasi O-ring dengan sedikit oli sebelum Anda mendorong fitting masuk.

    A cut O-ring caused the hydraulic leak on the press.

  17. 17

    thread(noun)

    /θred/

    ulir, drat

    the spiral ridge on a screw, bolt or inside a hole that lets parts screw together

    The hole has an M8 thread, so use an M8 bolt.

    Lubang ini berulir M8, jadi gunakan baut M8.

    Clean the threads carefully before applying thread-locking compound to the bolt.