コンテンツへスキップ

レッスン6/10 · 17語 · 覚えた単語 0

Machine elements

機械要素

  1. 1

    gasket(noun)

    /ˈɡæskɪt/

    ガスケット, パッキン

    a flat piece of soft material placed between two joined surfaces to stop gas or liquid leaking

    Always fit a new gasket when you reassemble the pump cover.

    ポンプのカバーを組み直すときは、必ず新しいガスケットを取り付けてください。

    Oil was leaking because the gasket was damaged.

    類義語sealwasherpacking
    対義語none
  2. 2

    pulley(noun)

    /ˈpʊli/

    プーリー, 滑車, ベルト車

    a wheel with a groove around it that carries a belt or rope to transmit power or lift loads

    Replace both pulleys if their grooves are badly worn.

    溝がひどく摩耗している場合は、両方のプーリーを交換してください。

    The motor pulley is smaller to reduce the fan speed.

    類義語blocksheavewinch
    対義語None
  3. 3

    rivet(noun)

    /ˈrɪvɪt/

    リベット, 鋲

    a short metal pin used to join metal sheets permanently by hammering or pressing its end flat

    The panels are joined with aluminium blind rivets.

    パネルはアルミ製のブラインドリベットで接合されている。

    Drill out the old rivet before fitting the new bracket.

    類義語fastenerboltpin
    対義語weldadhesive
  4. 4

    spur gear(noun)

    /spɜːr ɡɪr/

    平歯車

    the simplest type of gear, with straight teeth parallel to the shaft

    Spur gears are cheap to make but noisier than helical gears.

    平歯車は安価に製造できますが、はすば歯車よりも騒音が大きくなります。

    The feeder uses a pair of spur gears to reduce speed.

    類義語straight-cut gear
    対義語helical gearbevel gear
  5. 5

    washer(noun)

    /ˈwɑːʃər/

    座金, ワッシャー

    a thin flat ring placed under a nut or bolt head to spread the load or stop it loosening

    Put a flat washer under each nut to protect the painted surface.

    塗装面を保護するため、各ナットの下に平座金を入れてください。

    Spring washers stop the bolts loosening from vibration.

    類義語shimspacer
    対義語none
  6. 6

    belt drive(noun)

    /belt draɪv/

    ベルト伝動装置, ベルト駆動

    a system that uses a belt running over pulleys to pass power from one shaft to another

    Check the belt drive tension after the first 24 hours of running.

    運転開始から最初の24時間が経過したら、ベルト伝動装置の張力を点検してください。

    A belt drive is quieter and cheaper than a chain drive.

    類義語belt transmissionbelt power transfer
    対義語direct drivegear drive
  7. 7

    gearbox(noun)

    /ˈɡɪrbɑːks/

    減速機, ギアボックス, 歯車箱

    a closed housing containing a set of gears that changes the speed and turning force between a motor and a machine

    The conveyor motor is fitted with a 20 to 1 reduction gearbox.

    コンベヤのモーターには、減速比20対1の減速機が取り付けられている。

    Check the gearbox oil level during the weekly inspection.

    類義語transmissiongear case
    対義語None
  8. 8

    shaft(noun)

    /ʃɑːft/

    軸, シャフト

    a long round bar in a machine that turns and carries power from one part to another

    The motor drives the pump through a short steel shaft.

    モーターは、短い鋼製のシャフトを介してポンプを駆動する。

    A bent shaft was causing the vibration in the fan.

  9. 9

    bearing(noun)

    /ˈbeərɪŋ/

    軸受, ベアリング

    a machine part that supports a turning shaft and reduces friction between moving parts

    The noise is coming from a worn bearing in the gearbox.

    異音は、ギアボックス内の摩耗した軸受から出ている。

    Grease the conveyor bearings every 500 operating hours.

  10. 10

    ball bearing(noun)

    /ˌbɔːl ˈbeərɪŋ/

    玉軸受, ボールベアリング

    a bearing in which small steel balls roll between an inner and an outer ring

    The motor uses two sealed ball bearings that need no extra grease.

    このモーターには、追加のグリースが不要な密封型玉軸受が2個使われている。

    Order a 6205 deep groove ball bearing as a spare.

  11. 11

    roller bearing(noun)

    /ˌrəʊlə ˈbeərɪŋ/

    ころ軸受, ローラーベアリング

    a bearing that uses cylinders or tapered rollers instead of balls, so it can carry heavier loads

    The wheel hub runs on two tapered roller bearings.

    ホイールハブは、2個の円すいころ軸受で支えられている。

    We chose a roller bearing because the radial load is very high.

  12. 12

    gear(noun)

    /ɡɪə(r)/

    歯車, ギア

    a wheel with teeth around its edge that fits with another toothed wheel to pass on movement and power

    Two teeth on the drive gear were broken.

    駆動歯車の歯が2本折れていた。

    Changing the gear ratio will increase the output torque.

  13. 13

    coupling(noun)

    /ˈkʌplɪŋ/

    カップリング, 軸継手

    a device that joins the ends of two shafts so that power passes from one to the other

    A flexible coupling connects the motor to the pump shaft.

    フレキシブルカップリングが、モーターとポンプの軸をつないでいる。

    The rubber insert in the coupling had worn out.

  14. 14

    keyway(noun)

    /ˈkiːweɪ/

    キー溝, キーウェイ

    a slot cut in a shaft or hub where a key fits, so that the two turn together

    The keyway is milled after the shaft is turned to size.

    キー溝は、軸を所定の寸法に旋削した後にフライス加工される。

    A worn keyway lets the pulley slip on the shaft.

  15. 15

    bolt(noun)

    /bəʊlt/

    ボルト

    a metal rod with a head and a screw thread, used with a nut to hold parts together

    Use grade 8.8 bolts for the motor base.

    モーターベースには、強度区分8.8のボルトを使用してください。

    Two bolts on the guard were missing after maintenance.

  16. 16

    O-ring(noun)

    /ˈəʊ rɪŋ/

    Oリング, ゴムリング

    a rubber ring with a round cross-section that sits in a groove to seal a joint

    Lightly oil the O-ring before you push the fitting in.

    継手を押し込む前に、Oリングに軽く油を塗ってください。

    A cut O-ring caused the hydraulic leak on the press.

  17. 17

    thread(noun)

    /θred/

    ねじ山, ねじ

    the spiral ridge on a screw, bolt or inside a hole that lets parts screw together

    The hole has an M8 thread, so use an M8 bolt.

    この穴はM8のねじ山なので、M8のボルトを使ってください。

    Clean the threads carefully before applying thread-locking compound to the bolt.