본문으로 건너뛰기

레슨 6/10 · 17단어 · 외운 단어 0

Machine elements

기계 요소

  1. 1

    gasket(noun)

    /ˈɡæskɪt/

    개스킷, 가스켓

    a flat piece of soft material placed between two joined surfaces to stop gas or liquid leaking

    Always fit a new gasket when you reassemble the pump cover.

    펌프 커버를 재조립할 때는 항상 새 개스킷을 장착하십시오.

    Oil was leaking because the gasket was damaged.

    유의어sealwasherpacking
    반의어none
  2. 2

    pulley(noun)

    /ˈpʊli/

    풀리, 도르래

    a wheel with a groove around it that carries a belt or rope to transmit power or lift loads

    Replace both pulleys if their grooves are badly worn.

    홈이 심하게 마모되었다면 풀리 두 개를 모두 교체하십시오.

    The motor pulley is smaller to reduce the fan speed.

    유의어blocksheavewinch
    반의어None
  3. 3

    rivet(noun)

    /ˈrɪvɪt/

    리벳

    a short metal pin used to join metal sheets permanently by hammering or pressing its end flat

    The panels are joined with aluminium blind rivets.

    패널은 알루미늄 블라인드 리벳으로 접합되어 있다.

    Drill out the old rivet before fitting the new bracket.

    유의어fastenerboltpin
    반의어weldadhesive
  4. 4

    spur gear(noun)

    /spɜːr ɡɪr/

    평기어, 스퍼 기어

    the simplest type of gear, with straight teeth parallel to the shaft

    Spur gears are cheap to make but noisier than helical gears.

    평기어는 제작 비용이 저렴하지만 헬리컬 기어보다 소음이 큽니다.

    The feeder uses a pair of spur gears to reduce speed.

    유의어straight-cut gear
    반의어helical gearbevel gear
  5. 5

    washer(noun)

    /ˈwɑːʃər/

    와셔, 워셔

    a thin flat ring placed under a nut or bolt head to spread the load or stop it loosening

    Put a flat washer under each nut to protect the painted surface.

    도장된 표면을 보호하기 위해 각 너트 밑에 평와셔를 끼우세요.

    Spring washers stop the bolts loosening from vibration.

    유의어shimspacer
    반의어none
  6. 6

    belt drive(noun)

    /belt draɪv/

    벨트 구동장치, 벨트 전동장치

    a system that uses a belt running over pulleys to pass power from one shaft to another

    Check the belt drive tension after the first 24 hours of running.

    가동 후 첫 24시간이 지나면 벨트 구동장치의 장력을 점검하십시오.

    A belt drive is quieter and cheaper than a chain drive.

    유의어belt transmissionbelt power transfer
    반의어direct drivegear drive
  7. 7

    gearbox(noun)

    /ˈɡɪrbɑːks/

    기어박스, 감속기

    a closed housing containing a set of gears that changes the speed and turning force between a motor and a machine

    The conveyor motor is fitted with a 20 to 1 reduction gearbox.

    컨베이어 모터에는 20 대 1 감속기가 장착되어 있다.

    Check the gearbox oil level during the weekly inspection.

    유의어transmissiongear case
    반의어None
  8. 8

    shaft(noun)

    /ʃɑːft/

    축, 샤프트

    a long round bar in a machine that turns and carries power from one part to another

    The motor drives the pump through a short steel shaft.

    모터는 짧은 강철 축을 통해 펌프를 구동한다.

    A bent shaft was causing the vibration in the fan.

  9. 9

    bearing(noun)

    /ˈbeərɪŋ/

    베어링, 축받이

    a machine part that supports a turning shaft and reduces friction between moving parts

    The noise is coming from a worn bearing in the gearbox.

    소음은 기어박스의 마모된 베어링에서 나고 있다.

    Grease the conveyor bearings every 500 operating hours.

  10. 10

    ball bearing(noun)

    /ˌbɔːl ˈbeərɪŋ/

    볼 베어링, 구름 베어링

    a bearing in which small steel balls roll between an inner and an outer ring

    The motor uses two sealed ball bearings that need no extra grease.

    이 모터는 추가 그리스가 필요 없는 밀봉형 볼 베어링 두 개를 사용한다.

    Order a 6205 deep groove ball bearing as a spare.

  11. 11

    roller bearing(noun)

    /ˌrəʊlə ˈbeərɪŋ/

    롤러 베어링

    a bearing that uses cylinders or tapered rollers instead of balls, so it can carry heavier loads

    The wheel hub runs on two tapered roller bearings.

    휠 허브는 테이퍼 롤러 베어링 두 개로 회전한다.

    We chose a roller bearing because the radial load is very high.

  12. 12

    gear(noun)

    /ɡɪə(r)/

    기어, 톱니바퀴

    a wheel with teeth around its edge that fits with another toothed wheel to pass on movement and power

    Two teeth on the drive gear were broken.

    구동 기어의 이 두 개가 부러져 있었다.

    Changing the gear ratio will increase the output torque.

  13. 13

    coupling(noun)

    /ˈkʌplɪŋ/

    커플링, 축 이음

    a device that joins the ends of two shafts so that power passes from one to the other

    A flexible coupling connects the motor to the pump shaft.

    플렉시블 커플링이 모터를 펌프 축에 연결한다.

    The rubber insert in the coupling had worn out.

  14. 14

    keyway(noun)

    /ˈkiːweɪ/

    키홈, 키 홈

    a slot cut in a shaft or hub where a key fits, so that the two turn together

    The keyway is milled after the shaft is turned to size.

    키홈은 축을 치수에 맞게 선삭한 뒤에 밀링으로 가공한다.

    A worn keyway lets the pulley slip on the shaft.

  15. 15

    bolt(noun)

    /bəʊlt/

    볼트

    a metal rod with a head and a screw thread, used with a nut to hold parts together

    Use grade 8.8 bolts for the motor base.

    모터 베이스에는 강도 등급 8.8 볼트를 사용하십시오.

    Two bolts on the guard were missing after maintenance.

  16. 16

    O-ring(noun)

    /ˈəʊ rɪŋ/

    오링, O링

    a rubber ring with a round cross-section that sits in a groove to seal a joint

    Lightly oil the O-ring before you push the fitting in.

    피팅을 밀어 넣기 전에 오링에 기름을 살짝 바르세요.

    A cut O-ring caused the hydraulic leak on the press.

  17. 17

    thread(noun)

    /θred/

    나사산, 나사

    the spiral ridge on a screw, bolt or inside a hole that lets parts screw together

    The hole has an M8 thread, so use an M8 bolt.

    이 구멍은 M8 나사산이 있으니 M8 볼트를 사용하세요.

    Clean the threads carefully before applying thread-locking compound to the bolt.