Lumaktaw sa nilalaman

Aralin 6/10 · 17 salita · 0 natutunan

Machine elements

Mga elemento ng makina

  1. 1

    gasket(noun)

    /ˈɡæskɪt/

    gasket, pangsara ng siwang

    a flat piece of soft material placed between two joined surfaces to stop gas or liquid leaking

    Always fit a new gasket when you reassemble the pump cover.

    Laging maglagay ng bagong gasket kapag muling binubuo ang takip ng bomba.

    Oil was leaking because the gasket was damaged.

    Kasingkahulugansealwasherpacking
    Kasalungatnone
  2. 2

    pulley(noun)

    /ˈpʊli/

    puli, kalo

    a wheel with a groove around it that carries a belt or rope to transmit power or lift loads

    Replace both pulleys if their grooves are badly worn.

    Palitan ang parehong puli kung malala na ang pagkasira ng mga uka nito.

    The motor pulley is smaller to reduce the fan speed.

    Kasingkahuluganblocksheavewinch
    KasalungatNone
  3. 3

    rivet(noun)

    /ˈrɪvɪt/

    rebite, remache

    a short metal pin used to join metal sheets permanently by hammering or pressing its end flat

    The panels are joined with aluminium blind rivets.

    Ang mga panel ay pinagdugtong gamit ang aluminum na blind rivet.

    Drill out the old rivet before fitting the new bracket.

    Kasingkahuluganfastenerboltpin
    Kasalungatweldadhesive
  4. 4

    spur gear(noun)

    /spɜːr ɡɪr/

    spur gear, tuwid na gear

    the simplest type of gear, with straight teeth parallel to the shaft

    Spur gears are cheap to make but noisier than helical gears.

    Mura gawin ang mga spur gear ngunit mas maingay kaysa sa mga helical gear.

    The feeder uses a pair of spur gears to reduce speed.

    Kasingkahuluganstraight-cut gear
    Kasalungathelical gearbevel gear
  5. 5

    washer(noun)

    /ˈwɑːʃər/

    arandela

    a thin flat ring placed under a nut or bolt head to spread the load or stop it loosening

    Put a flat washer under each nut to protect the painted surface.

    Maglagay ng patag na arandela sa ilalim ng bawat nut upang maprotektahan ang pinturadong ibabaw.

    Spring washers stop the bolts loosening from vibration.

    Kasingkahuluganshimspacer
    Kasalungatnone
  6. 6

    belt drive(noun)

    /belt draɪv/

    belt drive, sistemang pang-sinturon

    a system that uses a belt running over pulleys to pass power from one shaft to another

    Check the belt drive tension after the first 24 hours of running.

    Suriin ang tensyon ng belt drive pagkatapos ng unang 24 na oras ng pagpapatakbo.

    A belt drive is quieter and cheaper than a chain drive.

    Kasingkahuluganbelt transmissionbelt power transfer
    Kasalungatdirect drivegear drive
  7. 7

    gearbox(noun)

    /ˈɡɪrbɑːks/

    kahon ng gear, transmisyon

    a closed housing containing a set of gears that changes the speed and turning force between a motor and a machine

    The conveyor motor is fitted with a 20 to 1 reduction gearbox.

    Nilagyan ang motor ng conveyor ng kahon ng gear na pambawas ng bilis na 20 to 1.

    Check the gearbox oil level during the weekly inspection.

    Kasingkahulugantransmissiongear case
    KasalungatNone
  8. 8

    shaft(noun)

    /ʃɑːft/

    baras, shaft

    a long round bar in a machine that turns and carries power from one part to another

    The motor drives the pump through a short steel shaft.

    Pinapaandar ng motor ang bomba sa pamamagitan ng maikling bakal na baras.

    A bent shaft was causing the vibration in the fan.

  9. 9

    bearing(noun)

    /ˈbeərɪŋ/

    bearing, pasanan ng baras

    a machine part that supports a turning shaft and reduces friction between moving parts

    The noise is coming from a worn bearing in the gearbox.

    Nanggagaling ang ingay sa isang sirang bearing sa gearbox.

    Grease the conveyor bearings every 500 operating hours.

  10. 10

    ball bearing(noun)

    /ˌbɔːl ˈbeərɪŋ/

    ball bearing, bearing na bola

    a bearing in which small steel balls roll between an inner and an outer ring

    The motor uses two sealed ball bearings that need no extra grease.

    Gumagamit ang motor ng dalawang selyadong ball bearing na hindi na nangangailangan ng dagdag na grasa.

    Order a 6205 deep groove ball bearing as a spare.

  11. 11

    roller bearing(noun)

    /ˌrəʊlə ˈbeərɪŋ/

    roller bearing, bearing na silindro

    a bearing that uses cylinders or tapered rollers instead of balls, so it can carry heavier loads

    The wheel hub runs on two tapered roller bearings.

    Umiikot ang hub ng gulong sa dalawang tapered roller bearing.

    We chose a roller bearing because the radial load is very high.

  12. 12

    gear(noun)

    /ɡɪə(r)/

    gear, lunday

    a wheel with teeth around its edge that fits with another toothed wheel to pass on movement and power

    Two teeth on the drive gear were broken.

    Dalawang ngipin ng drive gear ang nabali.

    Changing the gear ratio will increase the output torque.

  13. 13

    coupling(noun)

    /ˈkʌplɪŋ/

    kupling, pang-ugnay ng baras

    a device that joins the ends of two shafts so that power passes from one to the other

    A flexible coupling connects the motor to the pump shaft.

    Isang flexible na kupling ang nag-uugnay sa motor sa baras ng bomba.

    The rubber insert in the coupling had worn out.

  14. 14

    keyway(noun)

    /ˈkiːweɪ/

    keyway, uka ng susi

    a slot cut in a shaft or hub where a key fits, so that the two turn together

    The keyway is milled after the shaft is turned to size.

    Minimilling ang uka ng susi pagkatapos tornuhin ang baras sa tamang sukat.

    A worn keyway lets the pulley slip on the shaft.

  15. 15

    bolt(noun)

    /bəʊlt/

    bolt, pernong may tuerka

    a metal rod with a head and a screw thread, used with a nut to hold parts together

    Use grade 8.8 bolts for the motor base.

    Gumamit ng mga bolt na grade 8.8 para sa base ng motor.

    Two bolts on the guard were missing after maintenance.

  16. 16

    O-ring(noun)

    /ˈəʊ rɪŋ/

    O-ring, bilog na selyong goma

    a rubber ring with a round cross-section that sits in a groove to seal a joint

    Lightly oil the O-ring before you push the fitting in.

    Bahagyang langisan ang O-ring bago itulak papasok ang kabit.

    A cut O-ring caused the hydraulic leak on the press.

  17. 17

    thread(noun)

    /θred/

    sinulid ng turnilyo, sinulid

    the spiral ridge on a screw, bolt or inside a hole that lets parts screw together

    The hole has an M8 thread, so use an M8 bolt.

    May M8 na sinulid ang butas, kaya gumamit ng M8 na bolt.

    Clean the threads carefully before applying thread-locking compound to the bolt.