İçeriğe geç

Ders 6/10 · 17 kelime · Öğrenilen: 0

Machine elements

Makine elemanları

  1. 1

    gasket(noun)

    /ˈɡæskɪt/

    conta

    a flat piece of soft material placed between two joined surfaces to stop gas or liquid leaking

    Always fit a new gasket when you reassemble the pump cover.

    Pompa kapağını yeniden monte ederken her zaman yeni bir conta takın.

    Oil was leaking because the gasket was damaged.

    Eş anlamlılarsealwasherpacking
    Zıt anlamlılarnone
  2. 2

    pulley(noun)

    /ˈpʊli/

    kasnak

    a wheel with a groove around it that carries a belt or rope to transmit power or lift loads

    Replace both pulleys if their grooves are badly worn.

    Kanalları fazla aşınmışsa her iki kasnağı da değiştirin.

    The motor pulley is smaller to reduce the fan speed.

    Eş anlamlılarblocksheavewinch
    Zıt anlamlılarNone
  3. 3

    rivet(noun)

    /ˈrɪvɪt/

    perçin

    a short metal pin used to join metal sheets permanently by hammering or pressing its end flat

    The panels are joined with aluminium blind rivets.

    Paneller alüminyum kör perçinlerle birleştirilir.

    Drill out the old rivet before fitting the new bracket.

    Eş anlamlılarfastenerboltpin
    Zıt anlamlılarweldadhesive
  4. 4

    spur gear(noun)

    /spɜːr ɡɪr/

    düz dişli, düz dişli çark

    the simplest type of gear, with straight teeth parallel to the shaft

    Spur gears are cheap to make but noisier than helical gears.

    Düz dişlilerin üretimi ucuzdur ancak helisel dişlilere göre daha gürültülüdür.

    The feeder uses a pair of spur gears to reduce speed.

    Eş anlamlılarstraight-cut gear
    Zıt anlamlılarhelical gearbevel gear
  5. 5

    washer(noun)

    /ˈwɑːʃər/

    rondela, pul

    a thin flat ring placed under a nut or bolt head to spread the load or stop it loosening

    Put a flat washer under each nut to protect the painted surface.

    Boyalı yüzeyi korumak için her somunun altına düz bir rondela koyun.

    Spring washers stop the bolts loosening from vibration.

    Eş anlamlılarshimspacer
    Zıt anlamlılarnone
  6. 6

    belt drive(noun)

    /belt draɪv/

    kayış-kasnak tahriki, kayış tahriki, kayış-kasnak mekanizması

    a system that uses a belt running over pulleys to pass power from one shaft to another

    Check the belt drive tension after the first 24 hours of running.

    Çalışmanın ilk 24 saatinden sonra kayış tahrikinin gerginliğini kontrol edin.

    A belt drive is quieter and cheaper than a chain drive.

    Eş anlamlılarbelt transmissionbelt power transfer
    Zıt anlamlılardirect drivegear drive
  7. 7

    gearbox(noun)

    /ˈɡɪrbɑːks/

    dişli kutusu, redüktör

    a closed housing containing a set of gears that changes the speed and turning force between a motor and a machine

    The conveyor motor is fitted with a 20 to 1 reduction gearbox.

    Konveyör motoruna 20:1 oranlı bir redüktör takılıdır.

    Check the gearbox oil level during the weekly inspection.

    Eş anlamlılartransmissiongear case
    Zıt anlamlılarNone
  8. 8

    shaft(noun)

    /ʃɑːft/

    mil, şaft

    a long round bar in a machine that turns and carries power from one part to another

    The motor drives the pump through a short steel shaft.

    Motor, pompayı kısa bir çelik mil aracılığıyla çalıştırır.

    A bent shaft was causing the vibration in the fan.

  9. 9

    bearing(noun)

    /ˈbeərɪŋ/

    rulman, yatak

    a machine part that supports a turning shaft and reduces friction between moving parts

    The noise is coming from a worn bearing in the gearbox.

    Ses, dişli kutusundaki aşınmış bir rulmandan geliyor.

    Grease the conveyor bearings every 500 operating hours.

  10. 10

    ball bearing(noun)

    /ˌbɔːl ˈbeərɪŋ/

    bilyalı rulman

    a bearing in which small steel balls roll between an inner and an outer ring

    The motor uses two sealed ball bearings that need no extra grease.

    Motor, ilave gres gerektirmeyen iki contalı bilyalı rulman kullanır.

    Order a 6205 deep groove ball bearing as a spare.

  11. 11

    roller bearing(noun)

    /ˌrəʊlə ˈbeərɪŋ/

    makaralı rulman, silindirik makaralı rulman

    a bearing that uses cylinders or tapered rollers instead of balls, so it can carry heavier loads

    The wheel hub runs on two tapered roller bearings.

    Tekerlek poyrası iki konik makaralı rulman üzerinde döner.

    We chose a roller bearing because the radial load is very high.

  12. 12

    gear(noun)

    /ɡɪə(r)/

    dişli, dişli çark

    a wheel with teeth around its edge that fits with another toothed wheel to pass on movement and power

    Two teeth on the drive gear were broken.

    Tahrik dişlisindeki iki diş kırılmıştı.

    Changing the gear ratio will increase the output torque.

  13. 13

    coupling(noun)

    /ˈkʌplɪŋ/

    kaplin, akuplaj, mil bağlantısı

    a device that joins the ends of two shafts so that power passes from one to the other

    A flexible coupling connects the motor to the pump shaft.

    Esnek bir kaplin motoru pompa miline bağlar.

    The rubber insert in the coupling had worn out.

  14. 14

    keyway(noun)

    /ˈkiːweɪ/

    kama yuvası, kama kanalı

    a slot cut in a shaft or hub where a key fits, so that the two turn together

    The keyway is milled after the shaft is turned to size.

    Kama kanalı, mil ölçüsüne tornalandıktan sonra frezelenir.

    A worn keyway lets the pulley slip on the shaft.

  15. 15

    bolt(noun)

    /bəʊlt/

    cıvata

    a metal rod with a head and a screw thread, used with a nut to hold parts together

    Use grade 8.8 bolts for the motor base.

    Motor tabanı için 8.8 kalite cıvatalar kullanın.

    Two bolts on the guard were missing after maintenance.

  16. 16

    O-ring(noun)

    /ˈəʊ rɪŋ/

    O-ring, O-halka conta

    a rubber ring with a round cross-section that sits in a groove to seal a joint

    Lightly oil the O-ring before you push the fitting in.

    Bağlantı parçasını itmeden önce O-ringi hafifçe yağlayın.

    A cut O-ring caused the hydraulic leak on the press.

  17. 17

    thread(noun)

    /θred/

    diş, vida dişi

    the spiral ridge on a screw, bolt or inside a hole that lets parts screw together

    The hole has an M8 thread, so use an M8 bolt.

    Deliğin dişi M8 olduğu için M8 cıvata kullanın.

    Clean the threads carefully before applying thread-locking compound to the bolt.