コンテンツへスキップ

レッスン7/10 · 15語 · 覚えた単語 0

Welding and fabrication

溶接と製缶加工

  1. 1

    sheet metal(noun)

    /ʃiːt ˈmetl/

    板金, 薄板金属

    metal that has been rolled into thin flat pieces, used for covers, panels and boxes

    The control box is made of 1.5 mm sheet metal.

    制御盤は厚さ1.5 mmの板金で作られている。

    Our sheet metal shop can cut, bend and weld small batches.

    類義語metal platemetal sheet
    対義語bulk metalsolid metal
  2. 2

    welding(noun)

    /'weldi/

    溶接

    joining pieces of metal by heating them until they melt and fuse together

    Welding should only be done in the ventilated area.

    溶接は換気された場所でのみ行うこと。

    The welding procedure must be approved before production starts.

    類義語fusingsolderingbrazing
    対義語separationdisconnectiondetachment
  3. 3

    welder(noun)

    /ˈweldə(r)/

    溶接工, 溶接士

    a skilled worker whose job is to join metal parts by welding

    We need two certified welders for the pressure vessel job.

    圧力容器の作業には、資格を持った溶接工が2名必要です。

    The welder checked the joint fit-up before striking an arc.

  4. 4

    arc welding(noun)

    /ˈɑːk weldɪŋ/

    アーク溶接

    welding that uses an electric arc between an electrode and the metal to produce the heat

    Manual arc welding is still common for repairs on site.

    現場での補修では、手溶接によるアーク溶接が今も一般的です。

    Wear a proper helmet because arc welding produces strong UV light.

  5. 5

    MIG welding(noun)

    /ˈmɪɡ weldɪŋ/

    MIG溶接, ミグ溶接

    metal inert gas welding: arc welding with a wire fed continuously through a gun and protected by gas

    MIG welding is fast, so we use it for most steel frames.

    MIG溶接は速いので、ほとんどの鋼製フレームに使っています。

    Check the gas flow before you start MIG welding.

  6. 6

    TIG welding(noun)

    /ˈtɪɡ weldɪŋ/

    TIG溶接, ティグ溶接

    tungsten inert gas welding: precise arc welding with a tungsten electrode and argon gas, often for stainless steel

    The stainless steel pipes are joined by TIG welding.

    ステンレス鋼管はTIG溶接で接合されている。

    TIG welding is slower but gives very clean welds.

  7. 7

    electrode(noun)

    /ɪˈlektrəʊd/

    溶接棒, 電極

    a metal rod or wire that carries electric current to make the arc in welding, and often melts into the weld

    Keep the electrodes in a drying oven so they stay free of moisture.

    溶接棒は湿気を避けるため、乾燥器で保管してください。

    Use a 3.2 mm electrode for this plate thickness.

  8. 8

    filler metal(noun)

    /ˈfɪlə metl/

    溶加材, フィラーメタル

    metal added during welding or brazing to fill the joint

    Choose a filler metal that matches the base material.

    母材に適合する溶加材を選んでください。

    The welding procedure lists the approved filler metal.

  9. 9

    weld bead(noun)

    /ˈweld biːd/

    ビード, 溶接ビード

    the line of metal left on a joint after one pass of welding

    The weld bead should be smooth and even with no cracks.

    溶接ビードは、割れがなく滑らかで均一でなければならない。

    Grind the weld bead flush on the outside of the tank.

  10. 10

    porosity(noun)

    /pɔːˈrɒsəti/

    ブローホール, 気孔, ポロシティ

    a weld or casting defect made of small holes caused by gas trapped in the metal

    Porosity in the weld was caused by too little shielding gas.

    溶接部の気孔は、シールドガスの不足が原因だった。

    The X-ray showed porosity, so the joint must be repaired.

  11. 11

    distortion(noun)

    /dɪˈstɔːʃn/

    溶接変形, ひずみ, 歪み

    an unwanted change in the shape of a part caused by the heat of welding or cutting

    Tack weld both sides first to reduce distortion.

    変形を減らすため、まず両側を仮付け溶接してください。

    The long frame showed 3 mm of distortion after welding.

  12. 12

    press brake(noun)

    /ˈpres breɪk/

    プレスブレーキ, 曲げ加工機

    a machine that bends sheet metal into angles and shapes by pressing it between a punch and a die

    The brackets are bent to 90 degrees on the press brake.

    ブラケットはプレスブレーキで90度に曲げられる。

    Keep your hands clear of the tools when the press brake closes.

  13. 13

    laser cutting(noun)

    /ˈleɪzə kʌtɪŋ/

    レーザー切断, レーザー加工

    cutting metal sheet or plate with a powerful focused laser beam, usually controlled by CNC

    Laser cutting gives clean edges with no need for deburring.

    レーザー切断は切り口がきれいで、バリ取りが不要です。

    We send the DXF files to the supplier for laser cutting.

  14. 14

    fabrication(noun)

    /ˌfæbrɪˈkeɪʃn/

    製缶, 板金加工, 金属加工

    the work of making metal structures and parts by cutting, bending, welding and assembling

    The fabrication of the frame will take two weeks.

    フレームの製作には2週間かかります。

    He manages a steel fabrication shop with thirty workers.

  15. 15

    brazing(noun)

    /ˈbreɪzɪŋ/

    ろう付け

    joining metals with a melted filler metal, such as brass, without melting the base metals

    Copper pipes in the cooling system are joined by brazing.

    冷却システムの銅管はろう付けで接合されている。

    Brazing uses lower heat than welding, so there is less distortion.