본문으로 건너뛰기

레슨 5/10 · 17단어 · 외운 단어 0

Machining processes

절삭 가공

  1. 1

    coolant(noun)

    /ˈkuːlənt/

    절삭유, 냉각수

    a liquid used to cool and lubricate a tool and workpiece, or to cool an engine or machine

    Check the coolant concentration in the machine tank every Monday morning.

    매주 월요일 아침마다 기계 탱크의 절삭유 농도를 확인하십시오.

    Without enough coolant, the drill overheated and broke.

    유의어antifreezerefrigerant
    반의어heat sourceinsulator
  2. 2

    cutting tool(noun)

    /ˈkʌtɪŋ tuːl/

    절삭공구

    the sharp tool in a machine, such as a drill, insert or cutter, that removes material from the workpiece

    Carbide cutting tools last longer than high-speed steel ones.

    초경 절삭공구는 고속도강 공구보다 수명이 깁니다.

    Cutting tool costs are about eight percent of our machining budget.

    유의어bladecutteredge tool
    반의어blunt object
  3. 3

    lathe(noun)

    /leɪð/

    선반

    a machine that turns the workpiece while a fixed cutting tool removes material to make round parts

    The shafts are turned on a CNC lathe.

    샤프트는 CNC 선반에서 가공됩니다.

    He has ten years of experience on a manual lathe.

    유의어turning machineboring machine
    반의어None
  4. 4

    swarf(noun)

    /swɔ:f/

    절삭칩, 칩, 쇳밥

    the small pieces of metal that are cut off during machining

    Clear the swarf from the machine bed with a brush, not your hands.

    기계 베드의 절삭칩은 손이 아니라 브러시로 제거하십시오.

    Long swarf wrapped around the tool and damaged the surface.

    유의어shavingscuttingsdebrisgrindings
    반의어ingotbilletstock
  5. 5

    machining(noun)

    /məˈʃiːnɪŋ/

    기계가공, 절삭가공

    shaping metal or other material by cutting away parts of it with machine tools

    Machining the housing takes about forty minutes per piece.

    하우징 한 개를 기계가공하는 데 약 40분이 걸린다.

    The company offers precision machining for the automotive industry.

  6. 6

    turning(noun)

    /ˈtɜːnɪŋ/

    선삭, 선반 가공

    machining on a lathe, where the part rotates and the tool cuts its outside or inside diameter

    Turning is the main process for making pins and shafts.

    선삭은 핀과 축을 만드는 주된 공정이다.

    Leave 0.3 mm on the diameter for finish turning.

  7. 7

    milling(noun)

    /ˈmɪlɪŋ/

    밀링, 프라이스 가공

    machining in which a rotating cutter with several teeth removes material from a fixed workpiece

    The slots are cut by milling after the part is turned.

    부품을 선삭한 후 밀링으로 홈을 가공한다.

    Our new five-axis milling centre can make complex shapes.

  8. 8

    reaming(noun)

    /ˈriːmɪŋ/

    리밍

    finishing a drilled hole with a special tool to make it an exact size with a smooth surface

    The dowel holes need reaming to H7 after drilling.

    드릴 가공 후 다웰 구멍은 H7 공차로 리밍해야 한다.

    Leave about 0.2 mm of material for reaming.

  9. 9

    grinding(noun)

    /ˈɡraɪndɪŋ/

    연삭, research 연삭 가공

    using a turning abrasive wheel to remove small amounts of material and give a very accurate, smooth finish

    After heat treatment, the bearing seats are finished by grinding.

    열처리 후 베어링 안착부는 연삭으로 마무리한다.

    Surface grinding gives the plates a flatness within 5 microns.

  10. 10

    CNC(abbreviation)

    /ˌsiː en ˈsiː/

    CNC, 컴퓨터 수치 제어

    computer numerical control: control of a machine tool by a computer program that sets tool movements and speeds

    We are hiring a CNC operator for the night shift.

    야간 근무조 CNC 오퍼레이터를 채용합니다.

    The CNC program was checked on a simulator before the first cut.

  11. 11

    feed rate(noun)

    /ˈfiːd reɪt/

    이송 속도, 피드 레이트

    the speed at which the cutting tool moves into or along the workpiece

    Reduce the feed rate if the tool starts to chatter.

    공구에서 떨림(채터)이 생기기 시작하면 이송 속도를 낮추십시오.

    A higher feed rate cut the cycle time by twenty percent.

  12. 12

    spindle speed(noun)

    /ˈspɪndl spiːd/

    주축 회전수, 스핀들 속도

    how fast the machine spindle turns, measured in revolutions per minute

    Set the spindle speed to 1200 rpm for this aluminium part.

    이 알루미늄 부품은 주축 회전수를 1200 rpm으로 설정하십시오.

    Too high a spindle speed will burn the drill.

  13. 13

    depth of cut(noun)

    /ˌdepθ əv ˈkʌt/

    절삭 깊이, 절입량

    how deep the cutting tool goes into the material in one pass

    Use a depth of cut of 2 mm for roughing and 0.2 mm for finishing.

    황삭에는 절삭 깊이 2 mm, 정삭에는 0.2 mm를 사용하십시오.

    The insert broke because the depth of cut was too large.

  14. 14

    chuck(noun)

    /tʃʌk/

    척

    the device with jaws on a lathe or drill that holds the workpiece or tool firmly while it turns

    Never leave the chuck key in the chuck.

    척 핸들을 척에 꽂아 둔 채로 두지 마십시오.

    Thin parts can be crushed if the chuck pressure is too high.

  15. 15

    workpiece(noun)

    /ˈwɜːkpiːs/

    공작물, 가공물

    the piece of material or part that is being machined or worked on

    Make sure the workpiece is firmly clamped before starting the spindle.

    주축을 가동하기 전에 공작물이 단단히 고정되었는지 확인하십시오.

    The workpiece moved slightly, so the hole was out of position.

  16. 16

    jig(noun)

    /dʒɪɡ/

    지그

    a device that holds a part and guides the tool, so the same operation can be repeated accurately

    A drill jig makes sure every hole is in the same place.

    드릴 지그를 쓰면 모든 구멍이 같은 위치에 가공된다.

    The welding jig holds the frame square while it is tacked.

  17. 17

    fixture(noun)

    /ˈfɪkstʃə(r)/

    픽스처, 고정구

    a device that holds and locates a workpiece firmly in the correct position on a machine

    We designed a fixture that holds four parts at once on the milling machine.

    우리는 밀링 머신에서 부품 네 개를 한꺼번에 고정하는 픽스처를 설계했다.

    Changing the fixture adds fifteen minutes to the setup time.