본문으로 건너뛰기

레슨 9/10 · 15단어 · 외운 단어 0

Measurement and fault finding

측정과 고장 탐지

  1. 1

    calibrate(verb)

    /ˈkælɪbreɪt/

    교정하다, 보정하다

    to check and adjust a measuring instrument so that its readings are accurate

    All test instruments must be calibrated once a year.

    모든 시험 계측기는 연 1회 교정해야 한다.

    The pressure transmitter was calibrated before the system was started.

    유의어adjusttunecorrectstandardizeset
    반의어unbalancemisadjustdistort
  2. 2

    oscilloscope(noun)

    /əˈsɪləskəʊp/

    오실로스코프, 파형 측정기

    an instrument that shows how a voltage changes over time as a waveform on a screen

    The oscilloscope showed noise on the encoder signal.

    오실로스코프에서 엔코더 신호에 노이즈가 나타났다.

    Use an isolated oscilloscope probe when measuring the drive output.

    유의어scopewaveform monitor
    반의어N/A
  3. 3

    troubleshoot(verb)

    /ˈtrʌblʃuːt/

    문제 해결하다, 트러블슈팅하다, 장애를 진단하고 해결하다

    to find the cause of a technical problem and fix it, usually by checking possible causes one by one

    The technician spent an hour troubleshooting the Wi-Fi in the meeting room.

    기술자는 회의실 와이파이 문제를 해결하는 데 한 시간을 썼습니다.

    Follow these steps to troubleshoot common login problems.

    유의어diagnosefixresolvedebug
    반의어ignoreneglect
  4. 4

    multimeter(noun)

    /ˈmʌltimiːtə(r)/

    멀티미터, 멀티테스터

    a handheld meter that measures voltage, current and resistance, and can test continuity

    Set the multimeter to AC volts before checking the socket.

    콘센트를 점검하기 전에 멀티미터를 교류 전압으로 설정하세요.

    Every technician carries a digital multimeter in the tool bag.

  5. 5

    clamp meter(noun)

    /ˈklæmp ˌmiːtə(r)/

    클램프 미터, 클램프형 전류계

    a meter with jaws that close around a single wire to measure current without disconnecting it

    Use a clamp meter to check the current on each phase of the motor.

    클램프 미터로 모터의 각 상 전류를 확인하세요.

    Clamp only one conductor, or the clamp meter will read zero.

  6. 6

    insulation resistance tester(noun)

    /ˌɪnsjuˈleɪʃn rɪˈzɪstəns ˌtestə(r)/

    절연저항계, 절연저항 측정기

    an instrument that applies a high test voltage to measure how well cable or winding insulation prevents leakage

    Test the motor with an insulation resistance tester at 500 volts.

    절연저항계로 500볼트에서 모터를 시험하세요.

    Disconnect the electronics before using the insulation resistance tester on the cable.

  7. 7

    earth resistance tester(noun)

    /ˈɜːθ rɪˌzɪstəns ˌtestə(r)/

    접지저항계, 접지저항 측정기

    an instrument used to measure the resistance between an earth electrode and the surrounding ground

    The earth resistance tester showed 2 ohms, which meets the requirement.

    접지저항계가 2옴을 나타내 기준을 충족했다.

    Drive the test spikes into the soil before using the earth resistance tester.

  8. 8

    test lead(noun)

    /ˈtest liːd/

    테스트 리드, 시험용 리드선

    an insulated wire with a probe or clip that connects a meter to the circuit being measured

    Replace any test lead with cracked insulation before you use the meter.

    절연체에 금이 간 테스트 리드는 계측기를 사용하기 전에 교체하세요.

    Plug the red test lead into the volts socket of the meter.

  9. 9

    continuity test(noun)

    /ˌkɒntɪˈnjuːəti test/

    도통 시험, 통전 시험

    a test that checks whether a conductor or circuit forms a complete path with no breaks

    Do a continuity test on the earth conductor before energising the board.

    배전반에 전원을 투입하기 전에 접지 도체의 도통 시험을 실시하세요.

    The continuity test showed a broken wire inside the trailing cable.

  10. 10

    thermal imaging(noun)

    /ˌθɜːml ˈɪmɪdʒɪŋ/

    열화상 촬영, 열화상 진단

    the use of a special camera that shows heat, to find hot connections and overloaded parts

    A thermal imaging survey found three loose busbar joints.

    열화상 진단 결과 부스바 접속부 세 곳이 풀려 있는 것으로 나타났다.

    We do thermal imaging of all main panels every six months.

  11. 11

    commissioning(noun)

    /kəˈmɪʃənɪŋ/

    시운전, 커미셔닝

    the process of testing and checking new electrical equipment to prove it works correctly before handover

    Commissioning of the new switchboard is planned for next Tuesday.

    새 배전반의 시운전은 다음 주 화요일로 예정되어 있다.

    All test results must be recorded in the commissioning report.

  12. 12

    fault(noun)

    /fɔːlt/

    고장, 결함

    a defect or abnormal condition in an electrical circuit or device that stops it working correctly

    The breaker opened to isolate the fault in the cable.

    차단기가 작동하여 케이블의 고장 부위를 분리했다.

    Write the fault and the repair in the maintenance log.

  13. 13

    earth fault(noun)

    /ˈɜːθ fɔːlt/

    지락, 지락 고장

    a fault where a live conductor accidentally touches earth or a metal part connected to earth

    An earth fault in the outdoor light tripped the RCD.

    옥외 조명의 지락으로 누전차단기가 작동했다.

    The relay detected an earth fault on feeder number four.

  14. 14

    trip(verb)

    /trɪp/

    트립되다, 차단되다

    of a breaker or protection device: to switch off automatically because it detects a fault or overload

    The RCD in the outdoor lighting board keeps tripping whenever it rains.

    옥외 조명 분전반의 누전차단기가 비만 오면 계속 트립된다.

    The overload relay tripped because the pump was blocked.

  15. 15

    loose connection(noun)

    /ˌluːs kəˈnekʃn/

    접촉 불량, 접속 불량

    a terminal or joint that is not tight, which can cause heat, sparking or an intermittent fault

    A loose connection at the terminal caused the cable to burn.

    단자의 접촉 불량으로 케이블이 탔다.

    Most intermittent faults in panels are caused by a loose connection.