Langkau ke kandungan

Pelajaran 9/10 · 15 perkataan · 0 sudah dipelajari

Measurement and fault finding

Pengukuran dan pengesanan kerosakan

  1. 1

    calibrate(verb)

    /ˈkælɪbreɪt/

    menentukur, tentukur

    to check and adjust a measuring instrument so that its readings are accurate

    All test instruments must be calibrated once a year.

    Semua instrumen ujian mesti ditentukur setahun sekali.

    The pressure transmitter was calibrated before the system was started.

    Sinonimadjusttunecorrectstandardizeset
    Antonimunbalancemisadjustdistort
  2. 2

    oscilloscope(noun)

    /əˈsɪləskəʊp/

    osiloskop

    an instrument that shows how a voltage changes over time as a waveform on a screen

    The oscilloscope showed noise on the encoder signal.

    Osiloskop itu menunjukkan hingar pada isyarat pengekod.

    Use an isolated oscilloscope probe when measuring the drive output.

    Sinonimscopewaveform monitor
    AntonimN/A
  3. 3

    troubleshoot(verb)

    /ˈtrʌblʃuːt/

    menyelesaikan masalah, mendiagnosis masalah teknikal

    to find the cause of a technical problem and fix it, usually by checking possible causes one by one

    The technician spent an hour troubleshooting the Wi-Fi in the meeting room.

    Juruteknik itu menghabiskan satu jam menyelesaikan masalah Wi-Fi di bilik mesyuarat.

    Follow these steps to troubleshoot common login problems.

    Sinonimdiagnosefixresolvedebug
    Antonimignoreneglect
  4. 4

    multimeter(noun)

    /ˈmʌltimiːtə(r)/

    multimeter

    a handheld meter that measures voltage, current and resistance, and can test continuity

    Set the multimeter to AC volts before checking the socket.

    Tetapkan multimeter pada volt AC sebelum memeriksa soket.

    Every technician carries a digital multimeter in the tool bag.

  5. 5

    clamp meter(noun)

    /ˈklæmp ˌmiːtə(r)/

    meter pengapit, meter apit

    a meter with jaws that close around a single wire to measure current without disconnecting it

    Use a clamp meter to check the current on each phase of the motor.

    Gunakan meter pengapit untuk memeriksa arus pada setiap fasa motor.

    Clamp only one conductor, or the clamp meter will read zero.

  6. 6

    insulation resistance tester(noun)

    /ˌɪnsjuˈleɪʃn rɪˈzɪstəns ˌtestə(r)/

    penguji rintangan penebat, meter rintangan penebat

    an instrument that applies a high test voltage to measure how well cable or winding insulation prevents leakage

    Test the motor with an insulation resistance tester at 500 volts.

    Uji motor dengan penguji rintangan penebat pada 500 volt.

    Disconnect the electronics before using the insulation resistance tester on the cable.

  7. 7

    earth resistance tester(noun)

    /ˈɜːθ rɪˌzɪstəns ˌtestə(r)/

    penguji rintangan bumi, meter rintangan bumi

    an instrument used to measure the resistance between an earth electrode and the surrounding ground

    The earth resistance tester showed 2 ohms, which meets the requirement.

    Penguji rintangan bumi menunjukkan 2 ohm, yang memenuhi keperluan.

    Drive the test spikes into the soil before using the earth resistance tester.

  8. 8

    test lead(noun)

    /ˈtest liːd/

    kabel ujian, wayar penduga

    an insulated wire with a probe or clip that connects a meter to the circuit being measured

    Replace any test lead with cracked insulation before you use the meter.

    Gantikan mana-mana kabel ujian yang penebatnya retak sebelum anda menggunakan meter.

    Plug the red test lead into the volts socket of the meter.

  9. 9

    continuity test(noun)

    /ˌkɒntɪˈnjuːəti test/

    ujian kesinambungan

    a test that checks whether a conductor or circuit forms a complete path with no breaks

    Do a continuity test on the earth conductor before energising the board.

    Lakukan ujian kesinambungan pada konduktor bumi sebelum memberi tenaga kepada papan suis.

    The continuity test showed a broken wire inside the trailing cable.

  10. 10

    thermal imaging(noun)

    /ˌθɜːml ˈɪmɪdʒɪŋ/

    pengimejan terma, termografi inframerah

    the use of a special camera that shows heat, to find hot connections and overloaded parts

    A thermal imaging survey found three loose busbar joints.

    Tinjauan pengimejan terma menemui tiga sambungan bar bas yang longgar.

    We do thermal imaging of all main panels every six months.

  11. 11

    commissioning(noun)

    /kəˈmɪʃənɪŋ/

    pentauliahan

    the process of testing and checking new electrical equipment to prove it works correctly before handover

    Commissioning of the new switchboard is planned for next Tuesday.

    Pentauliahan papan suis baharu dirancang pada Selasa depan.

    All test results must be recorded in the commissioning report.

  12. 12

    fault(noun)

    /fɔːlt/

    kerosakan, kecacatan

    a defect or abnormal condition in an electrical circuit or device that stops it working correctly

    The breaker opened to isolate the fault in the cable.

    Pemutus litar terbuka untuk mengasingkan kerosakan pada kabel itu.

    Write the fault and the repair in the maintenance log.

  13. 13

    earth fault(noun)

    /ˈɜːθ fɔːlt/

    kerosakan bumi, kerosakan ke bumi

    a fault where a live conductor accidentally touches earth or a metal part connected to earth

    An earth fault in the outdoor light tripped the RCD.

    Kerosakan bumi pada lampu luar menyebabkan RCD tertrip.

    The relay detected an earth fault on feeder number four.

  14. 14

    trip(verb)

    /trɪp/

    tertrip, putus secara automatik

    of a breaker or protection device: to switch off automatically because it detects a fault or overload

    The RCD in the outdoor lighting board keeps tripping whenever it rains.

    RCD pada papan lampu luar sentiasa tertrip setiap kali hujan.

    The overload relay tripped because the pump was blocked.

  15. 15

    loose connection(noun)

    /ˌluːs kəˈnekʃn/

    sambungan longgar

    a terminal or joint that is not tight, which can cause heat, sparking or an intermittent fault

    A loose connection at the terminal caused the cable to burn.

    Sambungan longgar pada terminal menyebabkan kabel terbakar.

    Most intermittent faults in panels are caused by a loose connection.