Vai al contenuto

Lezione 9/10 · 15 parole · 0 imparate

Measurement and fault finding

Misurazioni e ricerca guasti

  1. 1

    calibrate(verb)

    /ˈkælɪbreɪt/

    tarare, calibrare

    to check and adjust a measuring instrument so that its readings are accurate

    All test instruments must be calibrated once a year.

    Tutti gli strumenti di prova devono essere tarati una volta all'anno.

    The pressure transmitter was calibrated before the system was started.

    Sinonimiadjusttunecorrectstandardizeset
    Contrariunbalancemisadjustdistort
  2. 2

    oscilloscope(noun)

    /əˈsɪləskəʊp/

    oscilloscopio

    an instrument that shows how a voltage changes over time as a waveform on a screen

    The oscilloscope showed noise on the encoder signal.

    L'oscilloscopio ha mostrato del rumore sul segnale dell'encoder.

    Use an isolated oscilloscope probe when measuring the drive output.

    Sinonimiscopewaveform monitor
    ContrariN/A
  3. 3

    troubleshoot(verb)

    /ˈtrʌblʃuːt/

    risolvere i problemi, fare troubleshooting

    to find the cause of a technical problem and fix it, usually by checking possible causes one by one

    The technician spent an hour troubleshooting the Wi-Fi in the meeting room.

    Il tecnico ha passato un'ora a risolvere i problemi del Wi-Fi nella sala riunioni.

    Follow these steps to troubleshoot common login problems.

    Sinonimidiagnosefixresolvedebug
    Contrariignoreneglect
  4. 4

    multimeter(noun)

    /ˈmʌltimiːtə(r)/

    multimetro, tester

    a handheld meter that measures voltage, current and resistance, and can test continuity

    Set the multimeter to AC volts before checking the socket.

    Imposta il multimetro su volt in corrente alternata prima di controllare la presa.

    Every technician carries a digital multimeter in the tool bag.

  5. 5

    clamp meter(noun)

    /ˈklæmp ˌmiːtə(r)/

    pinza amperometrica

    a meter with jaws that close around a single wire to measure current without disconnecting it

    Use a clamp meter to check the current on each phase of the motor.

    Usa una pinza amperometrica per controllare la corrente su ciascuna fase del motore.

    Clamp only one conductor, or the clamp meter will read zero.

  6. 6

    insulation resistance tester(noun)

    /ˌɪnsjuˈleɪʃn rɪˈzɪstəns ˌtestə(r)/

    megaohmmetro, misuratore di isolamento

    an instrument that applies a high test voltage to measure how well cable or winding insulation prevents leakage

    Test the motor with an insulation resistance tester at 500 volts.

    Prova il motore con un megaohmmetro a 500 volt.

    Disconnect the electronics before using the insulation resistance tester on the cable.

  7. 7

    earth resistance tester(noun)

    /ˈɜːθ rɪˌzɪstəns ˌtestə(r)/

    misuratore di terra, terrometro

    an instrument used to measure the resistance between an earth electrode and the surrounding ground

    The earth resistance tester showed 2 ohms, which meets the requirement.

    Il terrometro ha indicato 2 ohm, valore che soddisfa il requisito.

    Drive the test spikes into the soil before using the earth resistance tester.

  8. 8

    test lead(noun)

    /ˈtest liːd/

    puntale, cavo di misura

    an insulated wire with a probe or clip that connects a meter to the circuit being measured

    Replace any test lead with cracked insulation before you use the meter.

    Sostituisci qualsiasi puntale con l'isolamento incrinato prima di usare lo strumento.

    Plug the red test lead into the volts socket of the meter.

  9. 9

    continuity test(noun)

    /ˌkɒntɪˈnjuːəti test/

    prova di continuità

    a test that checks whether a conductor or circuit forms a complete path with no breaks

    Do a continuity test on the earth conductor before energising the board.

    Esegui una prova di continuità sul conduttore di terra prima di mettere in tensione il quadro.

    The continuity test showed a broken wire inside the trailing cable.

  10. 10

    thermal imaging(noun)

    /ˌθɜːml ˈɪmɪdʒɪŋ/

    termografia, imaging termico

    the use of a special camera that shows heat, to find hot connections and overloaded parts

    A thermal imaging survey found three loose busbar joints.

    Un'indagine termografica ha individuato tre giunzioni delle sbarre lente.

    We do thermal imaging of all main panels every six months.

  11. 11

    commissioning(noun)

    /kəˈmɪʃənɪŋ/

    collaudo, messa in servizio

    the process of testing and checking new electrical equipment to prove it works correctly before handover

    Commissioning of the new switchboard is planned for next Tuesday.

    La messa in servizio del nuovo quadro elettrico è prevista per martedì prossimo.

    All test results must be recorded in the commissioning report.

  12. 12

    fault(noun)

    /fɔːlt/

    guasto

    a defect or abnormal condition in an electrical circuit or device that stops it working correctly

    The breaker opened to isolate the fault in the cable.

    L'interruttore è intervenuto per isolare il guasto nel cavo.

    Write the fault and the repair in the maintenance log.

  13. 13

    earth fault(noun)

    /ˈɜːθ fɔːlt/

    guasto a terra

    a fault where a live conductor accidentally touches earth or a metal part connected to earth

    An earth fault in the outdoor light tripped the RCD.

    Un guasto a terra nell'illuminazione esterna ha fatto scattare l'interruttore differenziale.

    The relay detected an earth fault on feeder number four.

  14. 14

    trip(verb)

    /trɪp/

    scattare, intervenire

    of a breaker or protection device: to switch off automatically because it detects a fault or overload

    The RCD in the outdoor lighting board keeps tripping whenever it rains.

    Il differenziale del quadro dell'illuminazione esterna scatta ogni volta che piove.

    The overload relay tripped because the pump was blocked.

  15. 15

    loose connection(noun)

    /ˌluːs kəˈnekʃn/

    connessione allentata, contatto allentato

    a terminal or joint that is not tight, which can cause heat, sparking or an intermittent fault

    A loose connection at the terminal caused the cable to burn.

    Una connessione allentata al morsetto ha provocato la bruciatura del cavo.

    Most intermittent faults in panels are caused by a loose connection.