Langkau ke kandungan

Pelajaran 8/10 · 15 perkataan · 0 sudah dipelajari

Measurement and inspection

Pengukuran dan pemeriksaan

  1. 1

    accuracy(noun)

    /ˈækjərəsi/

    ketepatan, kejituan

    how close a measurement or result is to the true or correct value

    The accuracy of the new machine is within 5 microns.

    Ketepatan mesin baharu itu berada dalam lingkungan 5 mikron.

    Temperature changes can affect the accuracy of your measurements.

    Sinonimprecisioncorrectnessexactnesstruthfulnessvalidityreliability
    Antoniminaccuracyerrorimprecisionfalsenessincorrectness
  2. 2

    precision(noun)

    /prɪˈsɪʒn/

    kepersisan, ketepatan

    how close repeated measurements or results are to each other; also the quality of being very exact

    The company makes precision parts for medical devices.

    Syarikat itu membuat komponen kepersisan untuk peranti perubatan.

    Good precision means you get the same reading every time.

    Sinonimaccuracyexactnessfinenesscarefulnessmeticulousness
    Antonimimprecisioninaccuracycarelessnessvaguenessindefiniteness
  3. 3

    calibration(noun)

    /ˌkælɪˈbreɪʃn/

    penentukuran, kalibrasi

    checking a measuring instrument against a known standard and adjusting it so its readings are correct

    This caliper is overdue for calibration, so do not use it.

    Angkup ini sudah lewat untuk penentukuran, jadi jangan gunakannya.

    Every gauge has a calibration label showing the next due date.

    Sinonimadjustmentstandardizationtuningcorrection
    Antonimmisalignmentinaccuracyerror
  4. 4

    vernier caliper(noun)

    /ˈvɜːniə ˌkælɪpə(r)/

    angkup vernier, angkup

    a sliding measuring tool with jaws, used to measure outside, inside and depth sizes accurately

    Measure the outside diameter with a vernier caliper.

    Ukur diameter luar dengan angkup vernier.

    A vernier caliper is accurate to about 0.02 millimetres.

  5. 5

    micrometer(noun)

    /maɪˈkrɒmɪtə(r)/

    mikrometer, tolok skru mikrometer

    a precise measuring tool with a screw mechanism, used to measure small sizes to 0.01 mm or better

    Use a micrometer to check the bearing seat diameter.

    Gunakan mikrometer untuk memeriksa diameter dudukan bearing.

    Always zero the micrometer before you start measuring a part.

  6. 6

    dial indicator(noun)

    /ˈdaɪəl ɪndɪkeɪtə(r)/

    penunjuk dail, tolok dail

    a measuring instrument with a needle and dial that shows very small movements, such as runout

    Check the shaft runout with a dial indicator on a magnetic base.

    Periksa larian lesar aci dengan penunjuk dail pada tapak magnet.

    The dial indicator showed 0.05 mm of movement on the spindle.

  7. 7

    feeler gauge(noun)

    /ˈfiːlə ɡeɪdʒ/

    tolok perasa, tolok bilah

    a set of thin metal blades of exact thicknesses, used to measure small gaps

    Measure the gap between the coupling halves with a feeler gauge.

    Ukur celah antara dua separuh gandingan dengan tolok perasa.

    The valve clearance is checked with a 0.2 mm feeler gauge.

  8. 8

    gauge block(noun)

    /ˈɡeɪdʒ blɒk/

    blok tolok, blok tolok piawai

    a very accurate steel or ceramic block of exact size, used as a reference to check measuring tools

    We check our micrometers against a gauge block every week.

    Kami menyemak mikrometer kami berdasarkan blok tolok setiap minggu.

    Handle gauge blocks with gloves to avoid rust from your fingers.

  9. 9

    go/no-go gauge(noun)

    /ˌɡəʊ nəʊ ˈɡəʊ ɡeɪdʒ/

    tolok lulus/gagal, tolok had

    a gauge with two ends that quickly shows whether a hole or thread is within its size limits

    Operators check every tapped hole with a go/no-go gauge.

    Operator memeriksa setiap lubang bertap dengan tolok lulus/gagal.

    If the no-go end enters the hole, the part is rejected.

  10. 10

    surface plate(noun)

    /ˈsɜːfɪs pleɪt/

    plat permukaan, meja rujukan

    a very flat granite or cast iron table used as a reference surface for measuring and marking out

    Place the part on the surface plate to check its flatness.

    Letakkan komponen itu di atas plat permukaan untuk memeriksa kerataannya.

    The granite surface plate is calibrated once a year.

  11. 11

    CMM(abbreviation)

    /ˌsiː em ˈem/

    CMM, mesin pengukur koordinat

    coordinate measuring machine: a machine with a probe that measures the exact 3D shape and size of parts

    The first part off the machine is measured on the CMM.

    Komponen pertama yang keluar daripada mesin diukur pada CMM.

    The CMM report shows two holes out of position.

  12. 12

    first article inspection(noun)

    /ˌfɜːst ˈɑːtɪkl ɪnspekʃn/

    pemeriksaan artikel pertama, pemeriksaan sampel pertama

    a full check of the first part made in a new production run to confirm it meets the drawing

    Production cannot start until the first article inspection is approved.

    Pengeluaran tidak boleh dimulakan sehingga pemeriksaan artikel pertama diluluskan.

    The customer asked for a first article inspection report with every new part.

  13. 13

    NDT(abbreviation)

    /ˌen diː ˈtiː/

    NDT, ujian tanpa musnah

    non-destructive testing: methods of checking materials and welds for hidden defects without damaging them

    All pressure welds must pass NDT before the vessel is painted.

    Semua kimpalan bertekanan mesti lulus NDT sebelum bejana itu dicat.

    An NDT technician will check the crane hook for cracks.

  14. 14

    ultrasonic testing(noun)

    /ˌʌltrəˈsɒnɪk testɪŋ/

    ujian ultrasonik

    an NDT method that sends high-frequency sound waves into metal to find cracks or measure thickness

    Ultrasonic testing found a crack inside the shaft.

    Ujian ultrasonik mengesan retakan di dalam aci itu.

    We use ultrasonic testing to measure the remaining wall thickness of pipes.

  15. 15

    dye penetrant testing(noun)

    /ˌdaɪ ˈpenɪtrənt testɪŋ/

    ujian penetran pewarna

    an NDT method where a coloured liquid is put on a surface to show small cracks that reach the surface

    Dye penetrant testing showed a hairline crack at the weld toe.

    Ujian penetran pewarna menunjukkan retakan halus pada hujung kimpalan.

    Clean the surface well before dye penetrant testing.