İçeriğe geç

Ders 8/10 · 15 kelime · Öğrenilen: 0

Measurement and inspection

Ölçme ve muayene

  1. 1

    accuracy(noun)

    /ˈækjərəsi/

    doğruluk, ölçüm doğruluğu

    how close a measurement or result is to the true or correct value

    The accuracy of the new machine is within 5 microns.

    Yeni makinenin doğruluğu 5 mikron dahilindedir.

    Temperature changes can affect the accuracy of your measurements.

    Eş anlamlılarprecisioncorrectnessexactnesstruthfulnessvalidityreliability
    Zıt anlamlılarinaccuracyerrorimprecisionfalsenessincorrectness
  2. 2

    precision(noun)

    /prɪˈsɪʒn/

    hassasiyet, tekrarlanabilirlik, kesinlik

    how close repeated measurements or results are to each other; also the quality of being very exact

    The company makes precision parts for medical devices.

    Şirket, tıbbi cihazlar için hassas parçalar üretiyor.

    Good precision means you get the same reading every time.

    Eş anlamlılaraccuracyexactnessfinenesscarefulnessmeticulousness
    Zıt anlamlılarimprecisioninaccuracycarelessnessvaguenessindefiniteness
  3. 3

    calibration(noun)

    /ˌkælɪˈbreɪʃn/

    kalibrasyon, ayar

    checking a measuring instrument against a known standard and adjusting it so its readings are correct

    This caliper is overdue for calibration, so do not use it.

    Bu kumpasın kalibrasyon zamanı geçti, bu yüzden kullanmayın.

    Every gauge has a calibration label showing the next due date.

    Eş anlamlılaradjustmentstandardizationtuningcorrection
    Zıt anlamlılarmisalignmentinaccuracyerror
  4. 4

    vernier caliper(noun)

    /ˈvɜːniə ˌkælɪpə(r)/

    kumpas, verniyeli kumpas

    a sliding measuring tool with jaws, used to measure outside, inside and depth sizes accurately

    Measure the outside diameter with a vernier caliper.

    Dış çapı kumpasla ölçün.

    A vernier caliper is accurate to about 0.02 millimetres.

  5. 5

    micrometer(noun)

    /maɪˈkrɒmɪtə(r)/

    mikrometre

    a precise measuring tool with a screw mechanism, used to measure small sizes to 0.01 mm or better

    Use a micrometer to check the bearing seat diameter.

    Rulman yuvasının çapını kontrol etmek için mikrometre kullanın.

    Always zero the micrometer before you start measuring a part.

  6. 6

    dial indicator(noun)

    /ˈdaɪəl ɪndɪkeɪtə(r)/

    komparatör

    a measuring instrument with a needle and dial that shows very small movements, such as runout

    Check the shaft runout with a dial indicator on a magnetic base.

    Mil salgısını manyetik tabanlı bir komparatörle kontrol edin.

    The dial indicator showed 0.05 mm of movement on the spindle.

  7. 7

    feeler gauge(noun)

    /ˈfiːlə ɡeɪdʒ/

    yaprak tipi sentil, sentil

    a set of thin metal blades of exact thicknesses, used to measure small gaps

    Measure the gap between the coupling halves with a feeler gauge.

    Kaplin yarımları arasındaki boşluğu sentille ölçün.

    The valve clearance is checked with a 0.2 mm feeler gauge.

  8. 8

    gauge block(noun)

    /ˈɡeɪdʒ blɒk/

    mastar blok, gauge blok

    a very accurate steel or ceramic block of exact size, used as a reference to check measuring tools

    We check our micrometers against a gauge block every week.

    Mikrometrelerimizi her hafta bir mastar blokla kontrol ediyoruz.

    Handle gauge blocks with gloves to avoid rust from your fingers.

  9. 9

    go/no-go gauge(noun)

    /ˌɡəʊ nəʊ ˈɡəʊ ɡeɪdʒ/

    geçer-geçmez mastar, limit mastarı

    a gauge with two ends that quickly shows whether a hole or thread is within its size limits

    Operators check every tapped hole with a go/no-go gauge.

    Operatörler işlenmiş (kılavuz çekilmiş) her deliği geçer-geçmez mastarla kontrol eder.

    If the no-go end enters the hole, the part is rejected.

  10. 10

    surface plate(noun)

    /ˈsɜːfɪs pleɪt/

    kontrol mermeri, gönye tezgâhı

    a very flat granite or cast iron table used as a reference surface for measuring and marking out

    Place the part on the surface plate to check its flatness.

    Düzlüğünü kontrol etmek için parçayı kontrol mermerinin üzerine yerleştirin.

    The granite surface plate is calibrated once a year.

  11. 11

    CMM(abbreviation)

    /ˌsiː em ˈem/

    koordinat ölçüm makinesi, CMM

    coordinate measuring machine: a machine with a probe that measures the exact 3D shape and size of parts

    The first part off the machine is measured on the CMM.

    Makineden çıkan ilk parça koordinat ölçüm makinesinde ölçülür.

    The CMM report shows two holes out of position.

  12. 12

    first article inspection(noun)

    /ˌfɜːst ˈɑːtɪkl ɪnspekʃn/

    ilk ürün muayenesi, ilk parça kontrolü

    a full check of the first part made in a new production run to confirm it meets the drawing

    Production cannot start until the first article inspection is approved.

    İlk ürün muayenesi onaylanmadan üretime başlanamaz.

    The customer asked for a first article inspection report with every new part.

  13. 13

    NDT(abbreviation)

    /ˌen diː ˈtiː/

    tahribatsız muayene, tahribatsız test, NDT

    non-destructive testing: methods of checking materials and welds for hidden defects without damaging them

    All pressure welds must pass NDT before the vessel is painted.

    Tüm basınçlı kaynaklar, kap boyanmadan önce tahribatsız muayeneden geçmelidir.

    An NDT technician will check the crane hook for cracks.

  14. 14

    ultrasonic testing(noun)

    /ˌʌltrəˈsɒnɪk testɪŋ/

    ultrasonik muayene, ultrasonik test

    an NDT method that sends high-frequency sound waves into metal to find cracks or measure thickness

    Ultrasonic testing found a crack inside the shaft.

    Ultrasonik muayene milin içinde bir çatlak tespit etti.

    We use ultrasonic testing to measure the remaining wall thickness of pipes.

  15. 15

    dye penetrant testing(noun)

    /ˌdaɪ ˈpenɪtrənt testɪŋ/

    sıvı penetrant muayenesi, penetrant testi

    an NDT method where a coloured liquid is put on a surface to show small cracks that reach the surface

    Dye penetrant testing showed a hairline crack at the weld toe.

    Sıvı penetrant muayenesi kaynak ağzında kıl payı bir çatlak gösterdi.

    Clean the surface well before dye penetrant testing.