Aller au contenu

Leçon 8/10 · 15 mots · 0 appris

Measurement and inspection

Mesure et contrôle

  1. 1

    accuracy(noun)

    /ˈækjərəsi/

    précision, exactitude

    how close a measurement or result is to the true or correct value

    The accuracy of the new machine is within 5 microns.

    La précision de la nouvelle machine est de l'ordre de 5 microns.

    Temperature changes can affect the accuracy of your measurements.

    Synonymesprecisioncorrectnessexactnesstruthfulnessvalidityreliability
    Antonymesinaccuracyerrorimprecisionfalsenessincorrectness
  2. 2

    precision(noun)

    /prɪˈsɪʒn/

    fidélité, précision

    how close repeated measurements or results are to each other; also the quality of being very exact

    The company makes precision parts for medical devices.

    L'entreprise fabrique des pièces de précision pour des dispositifs médicaux.

    Good precision means you get the same reading every time.

    Synonymesaccuracyexactnessfinenesscarefulnessmeticulousness
    Antonymesimprecisioninaccuracycarelessnessvaguenessindefiniteness
  3. 3

    calibration(noun)

    /ˌkælɪˈbreɪʃn/

    étalonnage, calibration

    checking a measuring instrument against a known standard and adjusting it so its readings are correct

    This caliper is overdue for calibration, so do not use it.

    Cet pied à coulisse est en retard d'étalonnage ; ne l'utilisez pas.

    Every gauge has a calibration label showing the next due date.

    Synonymesadjustmentstandardizationtuningcorrection
    Antonymesmisalignmentinaccuracyerror
  4. 4

    vernier caliper(noun)

    /ˈvɜːniə ˌkælɪpə(r)/

    pied à coulisse

    a sliding measuring tool with jaws, used to measure outside, inside and depth sizes accurately

    Measure the outside diameter with a vernier caliper.

    Mesurez le diamètre extérieur avec un pied à coulisse.

    A vernier caliper is accurate to about 0.02 millimetres.

  5. 5

    micrometer(noun)

    /maɪˈkrɒmɪtə(r)/

    micromètre, palmer

    a precise measuring tool with a screw mechanism, used to measure small sizes to 0.01 mm or better

    Use a micrometer to check the bearing seat diameter.

    Utilisez un micromètre pour contrôler le diamètre du logement de roulement.

    Always zero the micrometer before you start measuring a part.

  6. 6

    dial indicator(noun)

    /ˈdaɪəl ɪndɪkeɪtə(r)/

    comparateur à cadran, comparateur

    a measuring instrument with a needle and dial that shows very small movements, such as runout

    Check the shaft runout with a dial indicator on a magnetic base.

    Contrôlez le faux-rond de l'arbre avec un comparateur à cadran sur socle magnétique.

    The dial indicator showed 0.05 mm of movement on the spindle.

  7. 7

    feeler gauge(noun)

    /ˈfiːlə ɡeɪdʒ/

    jauge d'épaisseur, calibre d'épaisseur

    a set of thin metal blades of exact thicknesses, used to measure small gaps

    Measure the gap between the coupling halves with a feeler gauge.

    Mesurez le jeu entre les demi-accouplements avec une jauge d'épaisseur.

    The valve clearance is checked with a 0.2 mm feeler gauge.

  8. 8

    gauge block(noun)

    /ˈɡeɪdʒ blɒk/

    cale étalon

    a very accurate steel or ceramic block of exact size, used as a reference to check measuring tools

    We check our micrometers against a gauge block every week.

    Nous vérifions nos micromètres avec une cale étalon chaque semaine.

    Handle gauge blocks with gloves to avoid rust from your fingers.

  9. 9

    go/no-go gauge(noun)

    /ˌɡəʊ nəʊ ˈɡəʊ ɡeɪdʒ/

    calibre passe/ne-passe-pas, calibre à limites

    a gauge with two ends that quickly shows whether a hole or thread is within its size limits

    Operators check every tapped hole with a go/no-go gauge.

    Les opérateurs contrôlent chaque trou taraudé avec un calibre passe/ne-passe-pas.

    If the no-go end enters the hole, the part is rejected.

  10. 10

    surface plate(noun)

    /ˈsɜːfɪs pleɪt/

    marbre de contrôle, marbre de traçage

    a very flat granite or cast iron table used as a reference surface for measuring and marking out

    Place the part on the surface plate to check its flatness.

    Posez la pièce sur le marbre pour vérifier sa planéité.

    The granite surface plate is calibrated once a year.

  11. 11

    CMM(abbreviation)

    /ˌsiː em ˈem/

    MMT, machine à mesurer tridimensionnelle

    coordinate measuring machine: a machine with a probe that measures the exact 3D shape and size of parts

    The first part off the machine is measured on the CMM.

    La première pièce sortie de la machine est mesurée sur la MMT.

    The CMM report shows two holes out of position.

  12. 12

    first article inspection(noun)

    /ˌfɜːst ˈɑːtɪkl ɪnspekʃn/

    contrôle de première pièce, inspection du premier article

    a full check of the first part made in a new production run to confirm it meets the drawing

    Production cannot start until the first article inspection is approved.

    La production ne peut pas démarrer tant que le contrôle de première pièce n'est pas approuvé.

    The customer asked for a first article inspection report with every new part.

  13. 13

    NDT(abbreviation)

    /ˌen diː ˈtiː/

    CND, contrôle non destructif

    non-destructive testing: methods of checking materials and welds for hidden defects without damaging them

    All pressure welds must pass NDT before the vessel is painted.

    Toutes les soudures sous pression doivent passer les CND avant la peinture de la cuve.

    An NDT technician will check the crane hook for cracks.

  14. 14

    ultrasonic testing(noun)

    /ˌʌltrəˈsɒnɪk testɪŋ/

    contrôle par ultrasons, contrôle ultrasonore

    an NDT method that sends high-frequency sound waves into metal to find cracks or measure thickness

    Ultrasonic testing found a crack inside the shaft.

    Le contrôle par ultrasons a révélé une fissure à l'intérieur de l'arbre.

    We use ultrasonic testing to measure the remaining wall thickness of pipes.

  15. 15

    dye penetrant testing(noun)

    /ˌdaɪ ˈpenɪtrənt testɪŋ/

    ressuage, contrôle par ressuage

    an NDT method where a coloured liquid is put on a surface to show small cracks that reach the surface

    Dye penetrant testing showed a hairline crack at the weld toe.

    Le ressuage a révélé une fissure capillaire au pied du cordon de soudure.

    Clean the surface well before dye penetrant testing.