Lumaktaw sa nilalaman

Aralin 8/10 · 15 salita · 0 natutunan

Measurement and inspection

Pagsukat at inspeksyon

  1. 1

    accuracy(noun)

    /ˈækjərəsi/

    katumpakan, kawastuhan

    how close a measurement or result is to the true or correct value

    The accuracy of the new machine is within 5 microns.

    Ang katumpakan ng bagong makina ay nasa loob ng 5 microns.

    Temperature changes can affect the accuracy of your measurements.

    Kasingkahuluganprecisioncorrectnessexactnesstruthfulnessvalidityreliability
    Kasalungatinaccuracyerrorimprecisionfalsenessincorrectness
  2. 2

    precision(noun)

    /prɪˈsɪʒn/

    presisyon, katumpakan

    how close repeated measurements or results are to each other; also the quality of being very exact

    The company makes precision parts for medical devices.

    Gumagawa ang kompanya ng mga piyesang may mataas na presisyon para sa mga kagamitang medikal.

    Good precision means you get the same reading every time.

    Kasingkahuluganaccuracyexactnessfinenesscarefulnessmeticulousness
    Kasalungatimprecisioninaccuracycarelessnessvaguenessindefiniteness
  3. 3

    calibration(noun)

    /ˌkælɪˈbreɪʃn/

    kalibrasyon, pagkakalibra

    checking a measuring instrument against a known standard and adjusting it so its readings are correct

    This caliper is overdue for calibration, so do not use it.

    Lampas na sa takdang petsa ng kalibrasyon ang caliper na ito, kaya huwag itong gamitin.

    Every gauge has a calibration label showing the next due date.

    Kasingkahuluganadjustmentstandardizationtuningcorrection
    Kasalungatmisalignmentinaccuracyerror
  4. 4

    vernier caliper(noun)

    /ˈvɜːniə ˌkælɪpə(r)/

    kalibreng bernier, kaliper

    a sliding measuring tool with jaws, used to measure outside, inside and depth sizes accurately

    Measure the outside diameter with a vernier caliper.

    Sukatin ang panlabas na diyametro gamit ang kalibreng bernier.

    A vernier caliper is accurate to about 0.02 millimetres.

  5. 5

    micrometer(noun)

    /maɪˈkrɒmɪtə(r)/

    mikrometro, panukat na may turnilyo

    a precise measuring tool with a screw mechanism, used to measure small sizes to 0.01 mm or better

    Use a micrometer to check the bearing seat diameter.

    Gumamit ng mikrometro upang suriin ang diyametro ng upuan ng tindig.

    Always zero the micrometer before you start measuring a part.

  6. 6

    dial indicator(noun)

    /ˈdaɪəl ɪndɪkeɪtə(r)/

    dayal na indikador, panukat na may dayal

    a measuring instrument with a needle and dial that shows very small movements, such as runout

    Check the shaft runout with a dial indicator on a magnetic base.

    Suriin ang pagkaliko ng ikot ng baras gamit ang dayal na indikador sa magnetikong patungan.

    The dial indicator showed 0.05 mm of movement on the spindle.

  7. 7

    feeler gauge(noun)

    /ˈfiːlə ɡeɪdʒ/

    panukat ng puwang, lámina ng panukat

    a set of thin metal blades of exact thicknesses, used to measure small gaps

    Measure the gap between the coupling halves with a feeler gauge.

    Sukatin ang puwang sa pagitan ng dalawang kalahati ng kopling gamit ang panukat ng puwang.

    The valve clearance is checked with a 0.2 mm feeler gauge.

  8. 8

    gauge block(noun)

    /ˈɡeɪdʒ blɒk/

    blokeng pamantayan, bloke ng panukat

    a very accurate steel or ceramic block of exact size, used as a reference to check measuring tools

    We check our micrometers against a gauge block every week.

    Tuwing linggo ay sinusuri namin ang aming mga mikrometro laban sa blokeng pamantayan.

    Handle gauge blocks with gloves to avoid rust from your fingers.

  9. 9

    go/no-go gauge(noun)

    /ˌɡəʊ nəʊ ˈɡəʊ ɡeɪdʒ/

    panukat na pasado/bagsak, panukat ng limitasyon

    a gauge with two ends that quickly shows whether a hole or thread is within its size limits

    Operators check every tapped hole with a go/no-go gauge.

    Sinusuri ng mga operator ang bawat butas na may sinulid gamit ang panukat na pasado/bagsak.

    If the no-go end enters the hole, the part is rejected.

  10. 10

    surface plate(noun)

    /ˈsɜːfɪs pleɪt/

    batayang patag na plato, plakang pang-sanggunian

    a very flat granite or cast iron table used as a reference surface for measuring and marking out

    Place the part on the surface plate to check its flatness.

    Ilagay ang piyesa sa batayang patag na plato upang suriin ang pagkapatag nito.

    The granite surface plate is calibrated once a year.

  11. 11

    CMM(abbreviation)

    /ˌsiː em ˈem/

    makinang pangsukat ng koordinado, CMM

    coordinate measuring machine: a machine with a probe that measures the exact 3D shape and size of parts

    The first part off the machine is measured on the CMM.

    Ang unang piyesang lumabas sa makina ay sinusukat sa CMM.

    The CMM report shows two holes out of position.

  12. 12

    first article inspection(noun)

    /ˌfɜːst ˈɑːtɪkl ɪnspekʃn/

    inspeksyon ng unang piyesa, pagsusuri sa unang produkto

    a full check of the first part made in a new production run to confirm it meets the drawing

    Production cannot start until the first article inspection is approved.

    Hindi puwedeng magsimula ang produksyon hangga't hindi naaprubahan ang inspeksyon ng unang piyesa.

    The customer asked for a first article inspection report with every new part.

  13. 13

    NDT(abbreviation)

    /ˌen diː ˈtiː/

    di-mapanirang pagsusuri, NDT

    non-destructive testing: methods of checking materials and welds for hidden defects without damaging them

    All pressure welds must pass NDT before the vessel is painted.

    Dapat pumasa sa NDT ang lahat ng hinang na pang-presyon bago pinturahan ang sisidlan.

    An NDT technician will check the crane hook for cracks.

  14. 14

    ultrasonic testing(noun)

    /ˌʌltrəˈsɒnɪk testɪŋ/

    pagsusuring ultrasoniko, pagsusuring gamit ang ultratunog

    an NDT method that sends high-frequency sound waves into metal to find cracks or measure thickness

    Ultrasonic testing found a crack inside the shaft.

    Natuklasan ng pagsusuring ultrasoniko ang bitak sa loob ng baras.

    We use ultrasonic testing to measure the remaining wall thickness of pipes.

  15. 15

    dye penetrant testing(noun)

    /ˌdaɪ ˈpenɪtrənt testɪŋ/

    pagsusuring may pangulay na penetrant, pagsusuring pangulay na tumatagos

    an NDT method where a coloured liquid is put on a surface to show small cracks that reach the surface

    Dye penetrant testing showed a hairline crack at the weld toe.

    Ipinakita ng pagsusuring may pangulay na penetrant ang manipis na bitak sa gilid ng hinang.

    Clean the surface well before dye penetrant testing.