Skip to content

Lesson 8/10 · 15 words · 0 learned

Measurement and inspection

  1. 1

    accuracy(noun)

    /ˈækjərəsi/

    how close a measurement or result is to the true or correct value

    The accuracy of the new machine is within 5 microns.

    Temperature changes can affect the accuracy of your measurements.

    Synonymsprecisioncorrectnessexactnesstruthfulnessvalidityreliability
    Antonymsinaccuracyerrorimprecisionfalsenessincorrectness
  2. 2

    precision(noun)

    /prɪˈsɪʒn/

    how close repeated measurements or results are to each other; also the quality of being very exact

    The company makes precision parts for medical devices.

    Good precision means you get the same reading every time.

    Synonymsaccuracyexactnessfinenesscarefulnessmeticulousness
    Antonymsimprecisioninaccuracycarelessnessvaguenessindefiniteness
  3. 3

    calibration(noun)

    /ˌkælɪˈbreɪʃn/

    checking a measuring instrument against a known standard and adjusting it so its readings are correct

    This caliper is overdue for calibration, so do not use it.

    Every gauge has a calibration label showing the next due date.

    Synonymsadjustmentstandardizationtuningcorrection
    Antonymsmisalignmentinaccuracyerror
  4. 4

    vernier caliper(noun)

    /ˈvɜːniə ˌkælɪpə(r)/

    a sliding measuring tool with jaws, used to measure outside, inside and depth sizes accurately

    Measure the outside diameter with a vernier caliper.

    A vernier caliper is accurate to about 0.02 millimetres.

  5. 5

    micrometer(noun)

    /maɪˈkrɒmɪtə(r)/

    a precise measuring tool with a screw mechanism, used to measure small sizes to 0.01 mm or better

    Use a micrometer to check the bearing seat diameter.

    Always zero the micrometer before you start measuring a part.

  6. 6

    dial indicator(noun)

    /ˈdaɪəl ɪndɪkeɪtə(r)/

    a measuring instrument with a needle and dial that shows very small movements, such as runout

    Check the shaft runout with a dial indicator on a magnetic base.

    The dial indicator showed 0.05 mm of movement on the spindle.

  7. 7

    feeler gauge(noun)

    /ˈfiːlə ɡeɪdʒ/

    a set of thin metal blades of exact thicknesses, used to measure small gaps

    Measure the gap between the coupling halves with a feeler gauge.

    The valve clearance is checked with a 0.2 mm feeler gauge.

  8. 8

    gauge block(noun)

    /ˈɡeɪdʒ blɒk/

    a very accurate steel or ceramic block of exact size, used as a reference to check measuring tools

    We check our micrometers against a gauge block every week.

    Handle gauge blocks with gloves to avoid rust from your fingers.

  9. 9

    go/no-go gauge(noun)

    /ˌɡəʊ nəʊ ˈɡəʊ ɡeɪdʒ/

    a gauge with two ends that quickly shows whether a hole or thread is within its size limits

    Operators check every tapped hole with a go/no-go gauge.

    If the no-go end enters the hole, the part is rejected.

  10. 10

    surface plate(noun)

    /ˈsɜːfɪs pleɪt/

    a very flat granite or cast iron table used as a reference surface for measuring and marking out

    Place the part on the surface plate to check its flatness.

    The granite surface plate is calibrated once a year.

  11. 11

    CMM(abbreviation)

    /ˌsiː em ˈem/

    coordinate measuring machine: a machine with a probe that measures the exact 3D shape and size of parts

    The first part off the machine is measured on the CMM.

    The CMM report shows two holes out of position.

  12. 12

    first article inspection(noun)

    /ˌfɜːst ˈɑːtɪkl ɪnspekʃn/

    a full check of the first part made in a new production run to confirm it meets the drawing

    Production cannot start until the first article inspection is approved.

    The customer asked for a first article inspection report with every new part.

  13. 13

    NDT(abbreviation)

    /ˌen diː ˈtiː/

    non-destructive testing: methods of checking materials and welds for hidden defects without damaging them

    All pressure welds must pass NDT before the vessel is painted.

    An NDT technician will check the crane hook for cracks.

  14. 14

    ultrasonic testing(noun)

    /ˌʌltrəˈsɒnɪk testɪŋ/

    an NDT method that sends high-frequency sound waves into metal to find cracks or measure thickness

    Ultrasonic testing found a crack inside the shaft.

    We use ultrasonic testing to measure the remaining wall thickness of pipes.

  15. 15

    dye penetrant testing(noun)

    /ˌdaɪ ˈpenɪtrənt testɪŋ/

    an NDT method where a coloured liquid is put on a surface to show small cracks that reach the surface

    Dye penetrant testing showed a hairline crack at the weld toe.

    Clean the surface well before dye penetrant testing.