Pular para o conteúdo

Lição 7/10 · 15 palavras · 0 aprendidas

Welding and fabrication

Soldagem e fabricação de estruturas

  1. 1

    sheet metal(noun)

    /ʃiːt ˈmetl/

    chapa metálica, chapa de metal

    metal that has been rolled into thin flat pieces, used for covers, panels and boxes

    The control box is made of 1.5 mm sheet metal.

    A caixa de comando é feita de chapa metálica de 1,5 mm.

    Our sheet metal shop can cut, bend and weld small batches.

    Sinônimosmetal platemetal sheet
    Antônimosbulk metalsolid metal
  2. 2

    welding(noun)

    /'weldi/

    soldagem, solda

    joining pieces of metal by heating them until they melt and fuse together

    Welding should only be done in the ventilated area.

    A soldagem só deve ser feita na área ventilada.

    The welding procedure must be approved before production starts.

    Sinônimosfusingsolderingbrazing
    Antônimosseparationdisconnectiondetachment
  3. 3

    welder(noun)

    /ˈweldə(r)/

    soldador

    a skilled worker whose job is to join metal parts by welding

    We need two certified welders for the pressure vessel job.

    Precisamos de dois soldadores certificados para o serviço do vaso de pressão.

    The welder checked the joint fit-up before striking an arc.

  4. 4

    arc welding(noun)

    /ˈɑːk weldɪŋ/

    soldagem a arco, solda a arco elétrico

    welding that uses an electric arc between an electrode and the metal to produce the heat

    Manual arc welding is still common for repairs on site.

    A soldagem a arco manual ainda é comum em reparos no local.

    Wear a proper helmet because arc welding produces strong UV light.

  5. 5

    MIG welding(noun)

    /ˈmɪɡ weldɪŋ/

    soldagem MIG, solda MIG

    metal inert gas welding: arc welding with a wire fed continuously through a gun and protected by gas

    MIG welding is fast, so we use it for most steel frames.

    A soldagem MIG é rápida, por isso a usamos na maioria das estruturas de aço.

    Check the gas flow before you start MIG welding.

  6. 6

    TIG welding(noun)

    /ˈtɪɡ weldɪŋ/

    soldagem TIG, solda TIG

    tungsten inert gas welding: precise arc welding with a tungsten electrode and argon gas, often for stainless steel

    The stainless steel pipes are joined by TIG welding.

    Os tubos de aço inoxidável são unidos por soldagem TIG.

    TIG welding is slower but gives very clean welds.

  7. 7

    electrode(noun)

    /ɪˈlektrəʊd/

    eletrodo, eletrodo revestido

    a metal rod or wire that carries electric current to make the arc in welding, and often melts into the weld

    Keep the electrodes in a drying oven so they stay free of moisture.

    Mantenha os eletrodos em uma estufa para que fiquem livres de umidade.

    Use a 3.2 mm electrode for this plate thickness.

  8. 8

    filler metal(noun)

    /ˈfɪlə metl/

    metal de adição

    metal added during welding or brazing to fill the joint

    Choose a filler metal that matches the base material.

    Escolha um metal de adição compatível com o metal de base.

    The welding procedure lists the approved filler metal.

  9. 9

    weld bead(noun)

    /ˈweld biːd/

    cordão de solda

    the line of metal left on a joint after one pass of welding

    The weld bead should be smooth and even with no cracks.

    O cordão de solda deve ser liso e uniforme, sem trincas.

    Grind the weld bead flush on the outside of the tank.

  10. 10

    porosity(noun)

    /pɔːˈrɒsəti/

    porosidade

    a weld or casting defect made of small holes caused by gas trapped in the metal

    Porosity in the weld was caused by too little shielding gas.

    A porosidade na solda foi causada por pouco gás de proteção.

    The X-ray showed porosity, so the joint must be repaired.

  11. 11

    distortion(noun)

    /dɪˈstɔːʃn/

    distorção, deformação

    an unwanted change in the shape of a part caused by the heat of welding or cutting

    Tack weld both sides first to reduce distortion.

    Faça primeiro a ponteação dos dois lados para reduzir a distorção.

    The long frame showed 3 mm of distortion after welding.

  12. 12

    press brake(noun)

    /ˈpres breɪk/

    dobradeira, prensa dobradeira

    a machine that bends sheet metal into angles and shapes by pressing it between a punch and a die

    The brackets are bent to 90 degrees on the press brake.

    As cantoneiras são dobradas a 90 graus na dobradeira.

    Keep your hands clear of the tools when the press brake closes.

  13. 13

    laser cutting(noun)

    /ˈleɪzə kʌtɪŋ/

    corte a laser

    cutting metal sheet or plate with a powerful focused laser beam, usually controlled by CNC

    Laser cutting gives clean edges with no need for deburring.

    O corte a laser deixa bordas limpas, sem necessidade de rebarbação.

    We send the DXF files to the supplier for laser cutting.

  14. 14

    fabrication(noun)

    /ˌfæbrɪˈkeɪʃn/

    fabricação, caldeiraria, fabricação de estruturas metálicas

    the work of making metal structures and parts by cutting, bending, welding and assembling

    The fabrication of the frame will take two weeks.

    A fabricação da estrutura levará duas semanas.

    He manages a steel fabrication shop with thirty workers.

  15. 15

    brazing(noun)

    /ˈbreɪzɪŋ/

    brasagem

    joining metals with a melted filler metal, such as brass, without melting the base metals

    Copper pipes in the cooling system are joined by brazing.

    Os tubos de cobre do sistema de refrigeração são unidos por brasagem.

    Brazing uses lower heat than welding, so there is less distortion.