Zum Inhalt springen

Lektion 7/10 · 15 Wörter · 0 gelernt

Welding and fabrication

Schweißen und Stahlbau

  1. 1

    sheet metal(noun)

    /ʃiːt ˈmetl/

    das Blech

    metal that has been rolled into thin flat pieces, used for covers, panels and boxes

    The control box is made of 1.5 mm sheet metal.

    Der Schaltkasten besteht aus 1,5 mm dickem Blech.

    Our sheet metal shop can cut, bend and weld small batches.

    Synonymemetal platemetal sheet
    Antonymebulk metalsolid metal
  2. 2

    welding(noun)

    /'weldi/

    das Schweißen

    joining pieces of metal by heating them until they melt and fuse together

    Welding should only be done in the ventilated area.

    Geschweißt werden darf nur im belüfteten Bereich.

    The welding procedure must be approved before production starts.

    Synonymefusingsolderingbrazing
    Antonymeseparationdisconnectiondetachment
  3. 3

    welder(noun)

    /ˈweldə(r)/

    der Schweißer, die Schweißerin

    a skilled worker whose job is to join metal parts by welding

    We need two certified welders for the pressure vessel job.

    Wir brauchen zwei zertifizierte Schweißer für den Druckbehälterauftrag.

    The welder checked the joint fit-up before striking an arc.

  4. 4

    arc welding(noun)

    /ˈɑːk weldɪŋ/

    das Lichtbogenschweißen

    welding that uses an electric arc between an electrode and the metal to produce the heat

    Manual arc welding is still common for repairs on site.

    Das Lichtbogenhandschweißen ist bei Reparaturen vor Ort nach wie vor üblich.

    Wear a proper helmet because arc welding produces strong UV light.

  5. 5

    MIG welding(noun)

    /ˈmɪɡ weldɪŋ/

    das MIG-Schweißen, das Metall-Schutzgasschweißen

    metal inert gas welding: arc welding with a wire fed continuously through a gun and protected by gas

    MIG welding is fast, so we use it for most steel frames.

    MIG-Schweißen ist schnell, deshalb verwenden wir es für die meisten Stahlrahmen.

    Check the gas flow before you start MIG welding.

  6. 6

    TIG welding(noun)

    /ˈtɪɡ weldɪŋ/

    das WIG-Schweißen, das Wolfram-Inertgasschweißen

    tungsten inert gas welding: precise arc welding with a tungsten electrode and argon gas, often for stainless steel

    The stainless steel pipes are joined by TIG welding.

    Die Edelstahlrohre werden durch WIG-Schweißen verbunden.

    TIG welding is slower but gives very clean welds.

  7. 7

    electrode(noun)

    /ɪˈlektrəʊd/

    die Schweißelektrode, die Elektrode

    a metal rod or wire that carries electric current to make the arc in welding, and often melts into the weld

    Keep the electrodes in a drying oven so they stay free of moisture.

    Bewahren Sie die Elektroden in einem Trockenschrank auf, damit sie feuchtigkeitsfrei bleiben.

    Use a 3.2 mm electrode for this plate thickness.

  8. 8

    filler metal(noun)

    /ˈfɪlə metl/

    der Schweißzusatz, der Zusatzwerkstoff

    metal added during welding or brazing to fill the joint

    Choose a filler metal that matches the base material.

    Wählen Sie einen Schweißzusatz, der zum Grundwerkstoff passt.

    The welding procedure lists the approved filler metal.

  9. 9

    weld bead(noun)

    /ˈweld biːd/

    die Schweißraupe, die Schweißnaht

    the line of metal left on a joint after one pass of welding

    The weld bead should be smooth and even with no cracks.

    Die Schweißraupe sollte glatt und gleichmäßig sein und keine Risse aufweisen.

    Grind the weld bead flush on the outside of the tank.

  10. 10

    porosity(noun)

    /pɔːˈrɒsəti/

    die Porosität, die Porenbildung

    a weld or casting defect made of small holes caused by gas trapped in the metal

    Porosity in the weld was caused by too little shielding gas.

    Die Porosität in der Schweißnaht wurde durch zu wenig Schutzgas verursacht.

    The X-ray showed porosity, so the joint must be repaired.

  11. 11

    distortion(noun)

    /dɪˈstɔːʃn/

    der Verzug, der Schweißverzug

    an unwanted change in the shape of a part caused by the heat of welding or cutting

    Tack weld both sides first to reduce distortion.

    Heften Sie zuerst beide Seiten, um den Verzug zu verringern.

    The long frame showed 3 mm of distortion after welding.

  12. 12

    press brake(noun)

    /ˈpres breɪk/

    die Abkantpresse

    a machine that bends sheet metal into angles and shapes by pressing it between a punch and a die

    The brackets are bent to 90 degrees on the press brake.

    Die Halterungen werden auf der Abkantpresse auf 90 Grad gebogen.

    Keep your hands clear of the tools when the press brake closes.

  13. 13

    laser cutting(noun)

    /ˈleɪzə kʌtɪŋ/

    das Laserschneiden, der Laserstrahlschnitt

    cutting metal sheet or plate with a powerful focused laser beam, usually controlled by CNC

    Laser cutting gives clean edges with no need for deburring.

    Laserschneiden liefert saubere Kanten, ein Entgraten ist nicht nötig.

    We send the DXF files to the supplier for laser cutting.

  14. 14

    fabrication(noun)

    /ˌfæbrɪˈkeɪʃn/

    die Fertigung, der Stahlbau, die Metallbearbeitung

    the work of making metal structures and parts by cutting, bending, welding and assembling

    The fabrication of the frame will take two weeks.

    Die Fertigung des Rahmens dauert zwei Wochen.

    He manages a steel fabrication shop with thirty workers.

  15. 15

    brazing(noun)

    /ˈbreɪzɪŋ/

    das Hartlöten, das Löten

    joining metals with a melted filler metal, such as brass, without melting the base metals

    Copper pipes in the cooling system are joined by brazing.

    Die Kupferrohre im Kühlsystem werden durch Hartlöten verbunden.

    Brazing uses lower heat than welding, so there is less distortion.