تخطَّ إلى المحتوى

الدرس 7/10 · 15 كلمة · تم تعلّم 0

Welding and fabrication

اللحام والتصنيع الإنشائي

  1. 1

    sheet metal(noun)

    /ʃiːt ˈmetl/

    صفائح معدنية, معدن صفائحي

    metal that has been rolled into thin flat pieces, used for covers, panels and boxes

    The control box is made of 1.5 mm sheet metal.

    صُنع صندوق التحكم من صفائح معدنية بسماكة 1.5 mm.

    Our sheet metal shop can cut, bend and weld small batches.

    المرادفاتmetal platemetal sheet
    الأضدادbulk metalsolid metal
  2. 2

    welding(noun)

    /'weldi/

    لحام

    joining pieces of metal by heating them until they melt and fuse together

    Welding should only be done in the ventilated area.

    يجب ألا يتم اللحام إلا في المنطقة جيدة التهوية.

    The welding procedure must be approved before production starts.

    المرادفاتfusingsolderingbrazing
    الأضدادseparationdisconnectiondetachment
  3. 3

    welder(noun)

    /ˈweldə(r)/

    لحّام

    a skilled worker whose job is to join metal parts by welding

    We need two certified welders for the pressure vessel job.

    نحتاج إلى لحّامَين معتمدَين لأعمال وعاء الضغط.

    The welder checked the joint fit-up before striking an arc.

  4. 4

    arc welding(noun)

    /ˈɑːk weldɪŋ/

    اللحام بالقوس الكهربائي, لحام القوس

    welding that uses an electric arc between an electrode and the metal to produce the heat

    Manual arc welding is still common for repairs on site.

    لا يزال اللحام اليدوي بالقوس الكهربائي شائعًا في أعمال الإصلاح في الموقع.

    Wear a proper helmet because arc welding produces strong UV light.

  5. 5

    MIG welding(noun)

    /ˈmɪɡ weldɪŋ/

    اللحام بالغاز الخامل المعدني, لحام ميغ

    metal inert gas welding: arc welding with a wire fed continuously through a gun and protected by gas

    MIG welding is fast, so we use it for most steel frames.

    اللحام بالغاز الخامل المعدني سريع، لذلك نستخدمه في معظم الهياكل الفولاذية.

    Check the gas flow before you start MIG welding.

  6. 6

    TIG welding(noun)

    /ˈtɪɡ weldɪŋ/

    اللحام بالتنغستن والغاز الخامل, لحام تيغ

    tungsten inert gas welding: precise arc welding with a tungsten electrode and argon gas, often for stainless steel

    The stainless steel pipes are joined by TIG welding.

    تُوصل أنابيب الفولاذ المقاوم للصدأ بواسطة اللحام بالتنغستن والغاز الخامل.

    TIG welding is slower but gives very clean welds.

  7. 7

    electrode(noun)

    /ɪˈlektrəʊd/

    قطب اللحام, إلكترود اللحام

    a metal rod or wire that carries electric current to make the arc in welding, and often melts into the weld

    Keep the electrodes in a drying oven so they stay free of moisture.

    احفظ أقطاب اللحام في فرن تجفيف حتى تبقى خالية من الرطوبة.

    Use a 3.2 mm electrode for this plate thickness.

  8. 8

    filler metal(noun)

    /ˈfɪlə metl/

    معدن الحشو, معدن اللحام المضاف

    metal added during welding or brazing to fill the joint

    Choose a filler metal that matches the base material.

    اختر معدن حشو يتوافق مع المعدن الأساسي.

    The welding procedure lists the approved filler metal.

  9. 9

    weld bead(noun)

    /ˈweld biːd/

    خرزة اللحام, شريط اللحام, وصلة اللحام

    the line of metal left on a joint after one pass of welding

    The weld bead should be smooth and even with no cracks.

    يجب أن تكون خرزة اللحام ناعمة ومتساوية وخالية من الشقوق.

    Grind the weld bead flush on the outside of the tank.

  10. 10

    porosity(noun)

    /pɔːˈrɒsəti/

    المسامية, مسامية اللحام

    a weld or casting defect made of small holes caused by gas trapped in the metal

    Porosity in the weld was caused by too little shielding gas.

    نتجت المسامية في اللحام عن قلة غاز الحماية.

    The X-ray showed porosity, so the joint must be repaired.

  11. 11

    distortion(noun)

    /dɪˈstɔːʃn/

    تشوه اللحام, التواء, تشوّه

    an unwanted change in the shape of a part caused by the heat of welding or cutting

    Tack weld both sides first to reduce distortion.

    ثبّت الجانبين بلحام نقطي أولًا لتقليل التشوه.

    The long frame showed 3 mm of distortion after welding.

  12. 12

    press brake(noun)

    /ˈpres breɪk/

    آلة ثني الصفائح, مكبس ثني, مكبس طي

    a machine that bends sheet metal into angles and shapes by pressing it between a punch and a die

    The brackets are bent to 90 degrees on the press brake.

    تُثنى الحوامل بزاوية 90 درجة على آلة ثني الصفائح.

    Keep your hands clear of the tools when the press brake closes.

  13. 13

    laser cutting(noun)

    /ˈleɪzə kʌtɪŋ/

    القطع بالليزر

    cutting metal sheet or plate with a powerful focused laser beam, usually controlled by CNC

    Laser cutting gives clean edges with no need for deburring.

    يعطي القطع بالليزر حوافّ نظيفة دون حاجة إلى إزالة الزوائد.

    We send the DXF files to the supplier for laser cutting.

  14. 14

    fabrication(noun)

    /ˌfæbrɪˈkeɪʃn/

    التصنيع المعدني, تصنيع الهياكل المعدنية, التشكيل المعدني

    the work of making metal structures and parts by cutting, bending, welding and assembling

    The fabrication of the frame will take two weeks.

    سيستغرق تصنيع الهيكل أسبوعين.

    He manages a steel fabrication shop with thirty workers.

  15. 15

    brazing(noun)

    /ˈbreɪzɪŋ/

    اللحام بالنحاس, لحام الإلحام, brazing

    joining metals with a melted filler metal, such as brass, without melting the base metals

    Copper pipes in the cooling system are joined by brazing.

    تُوصل أنابيب النحاس في نظام التبريد باللحام بالنحاس.

    Brazing uses lower heat than welding, so there is less distortion.