Langsung ke konten

Pelajaran 4/10 · 16 kata · 0 sudah hafal

Technical drawings and tolerances

Gambar teknik dan toleransi

  1. 1

    dimension(noun)

    /daɪˈmenʃn/

    dimensi, ukuran

    a measurement of length, width, height, diameter or angle that is shown on a drawing

    This dimension is critical, so measure it on every part.

    Dimensi ini bersifat kritis, jadi ukurlah pada setiap komponen.

    The overall dimensions of the frame are 1200 by 800 millimetres.

    Sinonimsizemeasurementextentscopeaspectmagnitude
    Antoniminsignificanceunimportanceminorityreduction
  2. 2

    chamfer(noun)

    /ˈtʃæmfər/

    sisi serong, potongan miring sudut

    a small angled cut along an edge or corner to remove sharpness or help parts fit together

    Add a 0.5 mm chamfer to all outside edges.

    Buat sisi serong 0,5 mm pada semua tepi luar.

    The chamfer on the shaft end helps the bearing slide on.

    Sinonimbevelcantsplayslopeangle
    Antonimsquare edgeright angleperpendicular
  3. 3

    technical drawing(noun)

    /ˌteknɪkl ˈdrɔːɪŋ/

    gambar teknik, gambar kerja

    an exact drawing that shows the shape, size, material and requirements of a part so it can be made

    Every machinist must be able to read a technical drawing.

    Setiap operator mesin perkakas harus mampu membaca gambar teknik.

    Check that you have the latest technical drawing before you start cutting.

  4. 4

    CAD(abbreviation)

    /kæd/

    desain berbantuan komputer, CAD

    computer-aided design: using software to create and change drawings and 3D models of parts

    The designer sent us the CAD model of the new bracket.

    Perancang mengirimkan model CAD braket baru itu kepada kami.

    We use CAD software to check that the parts fit before ordering material.

  5. 5

    orthographic projection(noun)

    /ˌɔːθəˌɡræfɪk prəˈdʒekʃn/

    proyeksi ortogonal, proyeksi ortografik

    a way of drawing an object as several flat views, such as front, top and side, at right angles

    European technical drawings normally use first-angle orthographic projection.

    Gambar teknik Eropa biasanya menggunakan proyeksi ortogonal sudut pertama.

    The part is shown in orthographic projection with three views.

  6. 6

    section view(noun)

    /ˈsekʃn vjuː/

    gambar potongan, pandangan potongan

    a view on a drawing that shows the inside of a part as if it had been cut through

    Add a section view so the machinist can see the internal groove.

    Tambahkan gambar potongan agar operator mesin dapat melihat alur bagian dalam.

    Section view B-B shows the depth of the blind hole.

  7. 7

    assembly drawing(noun)

    /əˈsembli drɔːɪŋ/

    gambar rakitan, gambar perakitan

    a drawing that shows how all the parts of a product fit together, usually with a parts list

    Follow the assembly drawing to fit the bearings in the correct order.

    Ikuti gambar rakitan untuk memasang bantalan dengan urutan yang benar.

    Item numbers on the assembly drawing match the bill of materials.

  8. 8

    title block(noun)

    /ˈtaɪtl blɒk/

    kepala gambar, kotak judul gambar, tabel identitas gambar

    the box on a drawing that gives the part name, number, material, scale, revision and approval

    The revision letter is shown in the title block at the bottom right.

    Huruf revisi tercantum pada kepala gambar di sudut kanan bawah.

    Check the material in the title block before you order stock.

  9. 9

    tolerance(noun)

    /ˈtɒlərəns/

    toleransi, dung sai

    the amount a dimension is allowed to vary from its stated size and still be acceptable

    The bore diameter has a tolerance of plus or minus 0.01 millimetres.

    Diameter lubang memiliki toleransi plus minus 0,01 milimeter.

    Three shafts were rejected because they were out of tolerance.

  10. 10

    clearance fit(noun)

    /ˈklɪərəns fɪt/

    suaian longgar, suaian renggang

    a fit where the hole is always slightly larger than the shaft, so the parts can move or slide

    The pin has a clearance fit so it can rotate freely in the hole.

    Pin tersebut memiliki suaian longgar sehingga dapat berputar bebas di dalam lubang.

    Use a clearance fit for parts that must be removed often.

  11. 11

    interference fit(noun)

    /ˌɪntəˈfɪərəns fɪt/

    suaian paksa, suaian interferensi

    a fit where the shaft is slightly larger than the hole, so the parts must be pressed or heated together

    The bearing is mounted with an interference fit on the shaft.

    Bantalan dipasang pada poros dengan suaian paksa.

    We heated the gear to assemble the interference fit without damage.

  12. 12

    GD&T(abbreviation)

    /ˌdʒiː diː ən ˈtiː/

    dimensi dan toleransi geometrik, GD&T

    geometric dimensioning and tolerancing: a system of symbols on drawings that controls form, orientation and position of features

    The new drawings use GD&T to control the position of the holes.

    Gambar-gambar baru menggunakan GD&T untuk mengendalikan posisi lubang-lubang.

    Our quality engineers attended a two-day GD&T training course.

  13. 13

    datum(noun)

    /ˈdeɪtəm/

    datum, bidang acuan, permukaan acuan

    a reference point, line or surface on a part from which other features are measured

    All hole positions are measured from datum A, the bottom face.

    Semua posisi lubang diukur dari datum A, yaitu permukaan bawah.

    Clamp the part on its datum surface before machining.

  14. 14

    surface roughness(noun)

    /ˈsɜːfɪs rʌfnəs/

    kekasaran permukaan

    the small peaks and valleys on a machined surface, usually given as an Ra value in micrometres

    The seal face needs a surface roughness of Ra 0.4 or better.

    Permukaan seal memerlukan kekasaran permukaan Ra 0,4 atau lebih halus.

    A worn insert increased the surface roughness of the bore.

  15. 15

    fillet(noun)

    /ˈfɪlɪt/

    radius dalam, lengkungan sudut dalam, fillet

    a rounded inside corner between two surfaces, used to reduce stress and make parts stronger

    A larger fillet at the shoulder will reduce the risk of cracking.

    Radius dalam yang lebih besar pada bahu poros akan mengurangi risiko retak.

    All internal corners have a 2 mm fillet unless stated otherwise.

  16. 16

    bill of materials(noun)

    /ˌbɪl əv məˈtɪəriəlz/

    daftar bahan, daftar material, BOM

    a list of all the parts, materials and quantities needed to build a product

    Purchasing orders parts directly from the bill of materials.

    Bagian pembelian memesan komponen langsung berdasarkan daftar bahan.

    The bill of materials lists 48 parts for the conveyor drive.