Pular para o conteúdo

Lição 4/10 · 16 palavras · 0 aprendidas

Technical drawings and tolerances

Desenhos técnicos e tolerâncias

  1. 1

    dimension(noun)

    /daɪˈmenʃn/

    cota, dimensão

    a measurement of length, width, height, diameter or angle that is shown on a drawing

    This dimension is critical, so measure it on every part.

    Esta cota é crítica, portanto meça-a em todas as peças.

    The overall dimensions of the frame are 1200 by 800 millimetres.

    Sinônimossizemeasurementextentscopeaspectmagnitude
    Antônimosinsignificanceunimportanceminorityreduction
  2. 2

    chamfer(noun)

    /ˈtʃæmfər/

    chanfro, chanfradura

    a small angled cut along an edge or corner to remove sharpness or help parts fit together

    Add a 0.5 mm chamfer to all outside edges.

    Faça um chanfro de 0,5 mm em todas as arestas externas.

    The chamfer on the shaft end helps the bearing slide on.

    Sinônimosbevelcantsplayslopeangle
    Antônimossquare edgeright angleperpendicular
  3. 3

    technical drawing(noun)

    /ˌteknɪkl ˈdrɔːɪŋ/

    desenho técnico

    an exact drawing that shows the shape, size, material and requirements of a part so it can be made

    Every machinist must be able to read a technical drawing.

    Todo operador de usinagem precisa saber ler um desenho técnico.

    Check that you have the latest technical drawing before you start cutting.

  4. 4

    CAD(abbreviation)

    /kæd/

    CAD, projeto assistido por computador

    computer-aided design: using software to create and change drawings and 3D models of parts

    The designer sent us the CAD model of the new bracket.

    O projetista nos enviou o modelo CAD do novo suporte.

    We use CAD software to check that the parts fit before ordering material.

  5. 5

    orthographic projection(noun)

    /ˌɔːθəˌɡræfɪk prəˈdʒekʃn/

    projeção ortogonal, projeção ortográfica

    a way of drawing an object as several flat views, such as front, top and side, at right angles

    European technical drawings normally use first-angle orthographic projection.

    Os desenhos técnicos europeus normalmente usam projeção ortogonal no primeiro diedro.

    The part is shown in orthographic projection with three views.

  6. 6

    section view(noun)

    /ˈsekʃn vjuː/

    vista em corte, corte

    a view on a drawing that shows the inside of a part as if it had been cut through

    Add a section view so the machinist can see the internal groove.

    Acrescente uma vista em corte para que o operador veja o canal interno.

    Section view B-B shows the depth of the blind hole.

  7. 7

    assembly drawing(noun)

    /əˈsembli drɔːɪŋ/

    desenho de conjunto, desenho de montagem

    a drawing that shows how all the parts of a product fit together, usually with a parts list

    Follow the assembly drawing to fit the bearings in the correct order.

    Siga o desenho de conjunto para montar os rolamentos na ordem correta.

    Item numbers on the assembly drawing match the bill of materials.

  8. 8

    title block(noun)

    /ˈtaɪtl blɒk/

    legenda, carimbo

    the box on a drawing that gives the part name, number, material, scale, revision and approval

    The revision letter is shown in the title block at the bottom right.

    A letra da revisão aparece na legenda, no canto inferior direito.

    Check the material in the title block before you order stock.

  9. 9

    tolerance(noun)

    /ˈtɒlərəns/

    tolerância, tolerância dimensional

    the amount a dimension is allowed to vary from its stated size and still be acceptable

    The bore diameter has a tolerance of plus or minus 0.01 millimetres.

    O diâmetro do furo tem tolerância de mais ou menos 0,01 milímetro.

    Three shafts were rejected because they were out of tolerance.

  10. 10

    clearance fit(noun)

    /ˈklɪərəns fɪt/

    ajuste com folga

    a fit where the hole is always slightly larger than the shaft, so the parts can move or slide

    The pin has a clearance fit so it can rotate freely in the hole.

    O pino tem ajuste com folga para poder girar livremente no furo.

    Use a clearance fit for parts that must be removed often.

  11. 11

    interference fit(noun)

    /ˌɪntəˈfɪərəns fɪt/

    ajuste com interferência, ajuste forçado

    a fit where the shaft is slightly larger than the hole, so the parts must be pressed or heated together

    The bearing is mounted with an interference fit on the shaft.

    O rolamento é montado no eixo com ajuste com interferência.

    We heated the gear to assemble the interference fit without damage.

  12. 12

    GD&T(abbreviation)

    /ˌdʒiː diː ən ˈtiː/

    GD&T, tolerância geométrica, dimensionamento e tolerância geométrica

    geometric dimensioning and tolerancing: a system of symbols on drawings that controls form, orientation and position of features

    The new drawings use GD&T to control the position of the holes.

    Os novos desenhos usam GD&T para controlar a posição dos furos.

    Our quality engineers attended a two-day GD&T training course.

  13. 13

    datum(noun)

    /ˈdeɪtəm/

    referência, superfície de referência, datum

    a reference point, line or surface on a part from which other features are measured

    All hole positions are measured from datum A, the bottom face.

    Todas as posições dos furos são medidas a partir da referência A, a face inferior.

    Clamp the part on its datum surface before machining.

  14. 14

    surface roughness(noun)

    /ˈsɜːfɪs rʌfnəs/

    rugosidade superficial, rugosidade

    the small peaks and valleys on a machined surface, usually given as an Ra value in micrometres

    The seal face needs a surface roughness of Ra 0.4 or better.

    A face de vedação precisa de rugosidade superficial de Ra 0,4 ou menor.

    A worn insert increased the surface roughness of the bore.

  15. 15

    fillet(noun)

    /ˈfɪlɪt/

    raio de concordância, arredondamento, filete

    a rounded inside corner between two surfaces, used to reduce stress and make parts stronger

    A larger fillet at the shoulder will reduce the risk of cracking.

    Um raio de concordância maior no ressalto reduzirá o risco de trincas.

    All internal corners have a 2 mm fillet unless stated otherwise.

  16. 16

    bill of materials(noun)

    /ˌbɪl əv məˈtɪəriəlz/

    lista de materiais, estrutura de produto

    a list of all the parts, materials and quantities needed to build a product

    Purchasing orders parts directly from the bill of materials.

    O setor de compras encomenda as peças diretamente a partir da lista de materiais.

    The bill of materials lists 48 parts for the conveyor drive.