ข้ามไปยังเนื้อหา

บทที่ 4/10 · 16 คำ · จำได้แล้ว 0

Technical drawings and tolerances

แบบทางวิศวกรรมและค่าพิกัดความเผื่อ

  1. 1

    dimension(noun)

    /daɪˈmenʃn/

    ขนาด, มิติ

    a measurement of length, width, height, diameter or angle that is shown on a drawing

    This dimension is critical, so measure it on every part.

    ขนาดนี้มีความสำคัญมาก จึงต้องวัดชิ้นส่วนทุกชิ้น

    The overall dimensions of the frame are 1200 by 800 millimetres.

    คำพ้องความหมายsizemeasurementextentscopeaspectmagnitude
    คำตรงข้ามinsignificanceunimportanceminorityreduction
  2. 2

    chamfer(noun)

    /ˈtʃæmfər/

    การลบมุม, รอยลบมุม, ชามเฟอร์

    a small angled cut along an edge or corner to remove sharpness or help parts fit together

    Add a 0.5 mm chamfer to all outside edges.

    ให้ลบมุมขนาด 0.5 มม. ที่ขอบด้านนอกทุกด้าน

    The chamfer on the shaft end helps the bearing slide on.

    คำพ้องความหมายbevelcantsplayslopeangle
    คำตรงข้ามsquare edgeright angleperpendicular
  3. 3

    technical drawing(noun)

    /ˌteknɪkl ˈdrɔːɪŋ/

    แบบทางวิศวกรรม, แบบงาน, แบบสั่งงาน

    an exact drawing that shows the shape, size, material and requirements of a part so it can be made

    Every machinist must be able to read a technical drawing.

    ช่างเครื่องทุกคนต้องอ่านแบบทางวิศวกรรมได้

    Check that you have the latest technical drawing before you start cutting.

  4. 4

    CAD(abbreviation)

    /kæd/

    แคด, การออกแบบด้วยคอมพิวเตอร์

    computer-aided design: using software to create and change drawings and 3D models of parts

    The designer sent us the CAD model of the new bracket.

    นักออกแบบส่งแบบจำลอง CAD ของขายึดตัวใหม่มาให้เรา

    We use CAD software to check that the parts fit before ordering material.

  5. 5

    orthographic projection(noun)

    /ˌɔːθəˌɡræfɪk prəˈdʒekʃn/

    การฉายภาพออร์โทกราฟิก, การฉายภาพมุมฉาก

    a way of drawing an object as several flat views, such as front, top and side, at right angles

    European technical drawings normally use first-angle orthographic projection.

    แบบทางวิศวกรรมของยุโรปมักใช้การฉายภาพออร์โทกราฟิกแบบมุมที่หนึ่ง

    The part is shown in orthographic projection with three views.

  6. 6

    section view(noun)

    /ˈsekʃn vjuː/

    ภาพตัด, รูปตัด

    a view on a drawing that shows the inside of a part as if it had been cut through

    Add a section view so the machinist can see the internal groove.

    เพิ่มภาพตัดเพื่อให้ช่างเครื่องมองเห็นร่องภายใน

    Section view B-B shows the depth of the blind hole.

  7. 7

    assembly drawing(noun)

    /əˈsembli drɔːɪŋ/

    แบบประกอบ, แบบแสดงการประกอบ

    a drawing that shows how all the parts of a product fit together, usually with a parts list

    Follow the assembly drawing to fit the bearings in the correct order.

    ให้ทำตามแบบประกอบเพื่อใส่ตลับลูกปืนตามลำดับที่ถูกต้อง

    Item numbers on the assembly drawing match the bill of materials.

  8. 8

    title block(noun)

    /ˈtaɪtl blɒk/

    ช่องชื่อแบบ, ตารางมุมแบบ

    the box on a drawing that gives the part name, number, material, scale, revision and approval

    The revision letter is shown in the title block at the bottom right.

    อักษรระบุฉบับแก้ไขแสดงอยู่ในช่องชื่อแบบที่มุมขวาล่าง

    Check the material in the title block before you order stock.

  9. 9

    tolerance(noun)

    /ˈtɒlərəns/

    ค่าพิกัดความเผื่อ, ความคลาดเคลื่อนที่ยอมรับได้, ทอเลอแรนซ์

    the amount a dimension is allowed to vary from its stated size and still be acceptable

    The bore diameter has a tolerance of plus or minus 0.01 millimetres.

    เส้นผ่านศูนย์กลางของรูมีค่าพิกัดความเผื่อ ±0.01 มิลลิเมตร

    Three shafts were rejected because they were out of tolerance.

  10. 10

    clearance fit(noun)

    /ˈklɪərəns fɪt/

    การสวมหลวม, ชุดสวมหลวม

    a fit where the hole is always slightly larger than the shaft, so the parts can move or slide

    The pin has a clearance fit so it can rotate freely in the hole.

    พินใช้การสวมหลวมเพื่อให้หมุนได้อย่างอิสระในรู

    Use a clearance fit for parts that must be removed often.

  11. 11

    interference fit(noun)

    /ˌɪntəˈfɪərəns fɪt/

    การสวมอัด, ชุดสวมอัด

    a fit where the shaft is slightly larger than the hole, so the parts must be pressed or heated together

    The bearing is mounted with an interference fit on the shaft.

    ตลับลูกปืนถูกติดตั้งบนเพลาด้วยการสวมอัด

    We heated the gear to assemble the interference fit without damage.

  12. 12

    GD&T(abbreviation)

    /ˌdʒiː diː ən ˈtiː/

    การกำหนดมิติและพิกัดความเผื่อทางเรขาคณิต, GD&T

    geometric dimensioning and tolerancing: a system of symbols on drawings that controls form, orientation and position of features

    The new drawings use GD&T to control the position of the holes.

    แบบใหม่ใช้ GD&T เพื่อควบคุมตำแหน่งของรู

    Our quality engineers attended a two-day GD&T training course.

  13. 13

    datum(noun)

    /ˈdeɪtəm/

    datum, ระนาบอ้างอิง, ผิวอ้างอิง, จุดอ้างอิง

    a reference point, line or surface on a part from which other features are measured

    All hole positions are measured from datum A, the bottom face.

    ตำแหน่งของรูทั้งหมดวัดจากผิวอ้างอิง A ซึ่งเป็นผิวด้านล่าง

    Clamp the part on its datum surface before machining.

  14. 14

    surface roughness(noun)

    /ˈsɜːfɪs rʌfnəs/

    ความขรุขระของผิว, ความหยาบผิว

    the small peaks and valleys on a machined surface, usually given as an Ra value in micrometres

    The seal face needs a surface roughness of Ra 0.4 or better.

    ผิวซีลต้องมีความขรุขระของผิวไม่เกิน Ra 0.4

    A worn insert increased the surface roughness of the bore.

  15. 15

    fillet(noun)

    /ˈfɪlɪt/

    ส่วนโค้งมุมใน, มุมมน, ฟิลเลต

    a rounded inside corner between two surfaces, used to reduce stress and make parts stronger

    A larger fillet at the shoulder will reduce the risk of cracking.

    การเพิ่มขนาดส่วนโค้งมุมในที่บ่าจะช่วยลดความเสี่ยงที่จะแตกร้าว

    All internal corners have a 2 mm fillet unless stated otherwise.

  16. 16

    bill of materials(noun)

    /ˌbɪl əv məˈtɪəriəlz/

    รายการวัสดุ, บัญชีรายการวัสดุ, BOM

    a list of all the parts, materials and quantities needed to build a product

    Purchasing orders parts directly from the bill of materials.

    ฝ่ายจัดซื้อสั่งชิ้นส่วนโดยตรงจากรายการวัสดุ

    The bill of materials lists 48 parts for the conveyor drive.