Langkau ke kandungan

Pelajaran 4/10 · 16 perkataan · 0 sudah dipelajari

Technical drawings and tolerances

Lukisan teknikal dan toleransi

  1. 1

    dimension(noun)

    /daɪˈmenʃn/

    dimensi, ukuran

    a measurement of length, width, height, diameter or angle that is shown on a drawing

    This dimension is critical, so measure it on every part.

    Dimensi ini kritikal, jadi ukurlah pada setiap komponen.

    The overall dimensions of the frame are 1200 by 800 millimetres.

    Sinonimsizemeasurementextentscopeaspectmagnitude
    Antoniminsignificanceunimportanceminorityreduction
  2. 2

    chamfer(noun)

    /ˈtʃæmfər/

    serong, bucu serong

    a small angled cut along an edge or corner to remove sharpness or help parts fit together

    Add a 0.5 mm chamfer to all outside edges.

    Tambahkan serong 0.5 mm pada semua tepi luar.

    The chamfer on the shaft end helps the bearing slide on.

    Sinonimbevelcantsplayslopeangle
    Antonimsquare edgeright angleperpendicular
  3. 3

    technical drawing(noun)

    /ˌteknɪkl ˈdrɔːɪŋ/

    lukisan teknikal

    an exact drawing that shows the shape, size, material and requirements of a part so it can be made

    Every machinist must be able to read a technical drawing.

    Setiap jurumesin mesti boleh membaca lukisan teknikal.

    Check that you have the latest technical drawing before you start cutting.

  4. 4

    CAD(abbreviation)

    /kæd/

    CAD, reka bentuk dibantu komputer

    computer-aided design: using software to create and change drawings and 3D models of parts

    The designer sent us the CAD model of the new bracket.

    Pereka itu menghantar model CAD braket baharu kepada kami.

    We use CAD software to check that the parts fit before ordering material.

  5. 5

    orthographic projection(noun)

    /ˌɔːθəˌɡræfɪk prəˈdʒekʃn/

    unjuran ortografik

    a way of drawing an object as several flat views, such as front, top and side, at right angles

    European technical drawings normally use first-angle orthographic projection.

    Lukisan teknikal Eropah biasanya menggunakan unjuran ortografik sudut pertama.

    The part is shown in orthographic projection with three views.

  6. 6

    section view(noun)

    /ˈsekʃn vjuː/

    pandangan keratan rentas, pandangan keratan

    a view on a drawing that shows the inside of a part as if it had been cut through

    Add a section view so the machinist can see the internal groove.

    Tambahkan pandangan keratan rentas supaya jurumesin dapat melihat alur dalaman.

    Section view B-B shows the depth of the blind hole.

  7. 7

    assembly drawing(noun)

    /əˈsembli drɔːɪŋ/

    lukisan pemasangan

    a drawing that shows how all the parts of a product fit together, usually with a parts list

    Follow the assembly drawing to fit the bearings in the correct order.

    Ikut lukisan pemasangan untuk memasang bearing mengikut urutan yang betul.

    Item numbers on the assembly drawing match the bill of materials.

  8. 8

    title block(noun)

    /ˈtaɪtl blɒk/

    blok tajuk

    the box on a drawing that gives the part name, number, material, scale, revision and approval

    The revision letter is shown in the title block at the bottom right.

    Huruf semakan ditunjukkan dalam blok tajuk di sebelah kanan bawah.

    Check the material in the title block before you order stock.

  9. 9

    tolerance(noun)

    /ˈtɒlərəns/

    toleransi

    the amount a dimension is allowed to vary from its stated size and still be acceptable

    The bore diameter has a tolerance of plus or minus 0.01 millimetres.

    Diameter lubang gerek itu mempunyai toleransi tambah atau tolak 0.01 milimeter.

    Three shafts were rejected because they were out of tolerance.

  10. 10

    clearance fit(noun)

    /ˈklɪərəns fɪt/

    pasangan kelegaan, pasangan longgar

    a fit where the hole is always slightly larger than the shaft, so the parts can move or slide

    The pin has a clearance fit so it can rotate freely in the hole.

    Pin itu mempunyai pasangan kelegaan supaya ia boleh berputar bebas dalam lubang.

    Use a clearance fit for parts that must be removed often.

  11. 11

    interference fit(noun)

    /ˌɪntəˈfɪərəns fɪt/

    pasangan sesak, pasangan interferens

    a fit where the shaft is slightly larger than the hole, so the parts must be pressed or heated together

    The bearing is mounted with an interference fit on the shaft.

    Bearing itu dipasang pada aci dengan pasangan sesak.

    We heated the gear to assemble the interference fit without damage.

  12. 12

    GD&T(abbreviation)

    /ˌdʒiː diː ən ˈtiː/

    GD&T, pendimensian dan toleransi geometri

    geometric dimensioning and tolerancing: a system of symbols on drawings that controls form, orientation and position of features

    The new drawings use GD&T to control the position of the holes.

    Lukisan baharu itu menggunakan GD&T untuk mengawal kedudukan lubang.

    Our quality engineers attended a two-day GD&T training course.

  13. 13

    datum(noun)

    /ˈdeɪtəm/

    datum, permukaan rujukan

    a reference point, line or surface on a part from which other features are measured

    All hole positions are measured from datum A, the bottom face.

    Semua kedudukan lubang diukur dari datum A, iaitu muka bawah.

    Clamp the part on its datum surface before machining.

  14. 14

    surface roughness(noun)

    /ˈsɜːfɪs rʌfnəs/

    kekasaran permukaan

    the small peaks and valleys on a machined surface, usually given as an Ra value in micrometres

    The seal face needs a surface roughness of Ra 0.4 or better.

    Muka seal memerlukan kekasaran permukaan Ra 0.4 atau lebih baik.

    A worn insert increased the surface roughness of the bore.

  15. 15

    fillet(noun)

    /ˈfɪlɪt/

    bucu bulat dalam, jejari sudut

    a rounded inside corner between two surfaces, used to reduce stress and make parts stronger

    A larger fillet at the shoulder will reduce the risk of cracking.

    Bucu bulat dalam yang lebih besar pada bahu akan mengurangkan risiko keretakan.

    All internal corners have a 2 mm fillet unless stated otherwise.

  16. 16

    bill of materials(noun)

    /ˌbɪl əv məˈtɪəriəlz/

    senarai bahan, BOM

    a list of all the parts, materials and quantities needed to build a product

    Purchasing orders parts directly from the bill of materials.

    Bahagian pembelian memesan komponen terus daripada senarai bahan.

    The bill of materials lists 48 parts for the conveyor drive.