Vai al contenuto

Lezione 4/10 · 16 parole · 0 imparate

Technical drawings and tolerances

Disegni tecnici e tolleranze

  1. 1

    dimension(noun)

    /daɪˈmenʃn/

    quota, dimensione

    a measurement of length, width, height, diameter or angle that is shown on a drawing

    This dimension is critical, so measure it on every part.

    Questa quota è critica, quindi va misurata su ogni pezzo.

    The overall dimensions of the frame are 1200 by 800 millimetres.

    Sinonimisizemeasurementextentscopeaspectmagnitude
    Contrariinsignificanceunimportanceminorityreduction
  2. 2

    chamfer(noun)

    /ˈtʃæmfər/

    smusso

    a small angled cut along an edge or corner to remove sharpness or help parts fit together

    Add a 0.5 mm chamfer to all outside edges.

    Eseguire uno smusso da 0,5 mm su tutti gli spigoli esterni.

    The chamfer on the shaft end helps the bearing slide on.

    Sinonimibevelcantsplayslopeangle
    Contrarisquare edgeright angleperpendicular
  3. 3

    technical drawing(noun)

    /ˌteknɪkl ˈdrɔːɪŋ/

    disegno tecnico

    an exact drawing that shows the shape, size, material and requirements of a part so it can be made

    Every machinist must be able to read a technical drawing.

    Ogni operatore alle macchine utensili deve saper leggere un disegno tecnico.

    Check that you have the latest technical drawing before you start cutting.

  4. 4

    CAD(abbreviation)

    /kæd/

    CAD, progettazione assistita da computer

    computer-aided design: using software to create and change drawings and 3D models of parts

    The designer sent us the CAD model of the new bracket.

    Il progettista ci ha inviato il modello CAD della nuova staffa.

    We use CAD software to check that the parts fit before ordering material.

  5. 5

    orthographic projection(noun)

    /ˌɔːθəˌɡræfɪk prəˈdʒekʃn/

    proiezione ortogonale, proiezioni ortogonali

    a way of drawing an object as several flat views, such as front, top and side, at right angles

    European technical drawings normally use first-angle orthographic projection.

    I disegni tecnici europei usano normalmente la proiezione ortogonale con il metodo del primo diedro.

    The part is shown in orthographic projection with three views.

  6. 6

    section view(noun)

    /ˈsekʃn vjuː/

    vista in sezione, sezione

    a view on a drawing that shows the inside of a part as if it had been cut through

    Add a section view so the machinist can see the internal groove.

    Aggiungi una vista in sezione così che l'operatore possa vedere la gola interna.

    Section view B-B shows the depth of the blind hole.

  7. 7

    assembly drawing(noun)

    /əˈsembli drɔːɪŋ/

    disegno di montaggio, disegno di assieme

    a drawing that shows how all the parts of a product fit together, usually with a parts list

    Follow the assembly drawing to fit the bearings in the correct order.

    Segui il disegno di montaggio per inserire i cuscinetti nell'ordine corretto.

    Item numbers on the assembly drawing match the bill of materials.

  8. 8

    title block(noun)

    /ˈtaɪtl blɒk/

    cartiglio

    the box on a drawing that gives the part name, number, material, scale, revision and approval

    The revision letter is shown in the title block at the bottom right.

    La lettera di revisione è indicata nel cartiglio in basso a destra.

    Check the material in the title block before you order stock.

  9. 9

    tolerance(noun)

    /ˈtɒlərəns/

    tolleranza

    the amount a dimension is allowed to vary from its stated size and still be acceptable

    The bore diameter has a tolerance of plus or minus 0.01 millimetres.

    Il diametro del foro ha una tolleranza di più o meno 0,01 millimetri.

    Three shafts were rejected because they were out of tolerance.

  10. 10

    clearance fit(noun)

    /ˈklɪərəns fɪt/

    accoppiamento con gioco

    a fit where the hole is always slightly larger than the shaft, so the parts can move or slide

    The pin has a clearance fit so it can rotate freely in the hole.

    Il perno ha un accoppiamento con gioco in modo da poter ruotare liberamente nel foro.

    Use a clearance fit for parts that must be removed often.

  11. 11

    interference fit(noun)

    /ˌɪntəˈfɪərəns fɪt/

    accoppiamento con interferenza, accoppiamento forzato

    a fit where the shaft is slightly larger than the hole, so the parts must be pressed or heated together

    The bearing is mounted with an interference fit on the shaft.

    Il cuscinetto è montato sull'albero con un accoppiamento con interferenza.

    We heated the gear to assemble the interference fit without damage.

  12. 12

    GD&T(abbreviation)

    /ˌdʒiː diː ən ˈtiː/

    GD&T, quotatura e tolleranze geometriche

    geometric dimensioning and tolerancing: a system of symbols on drawings that controls form, orientation and position of features

    The new drawings use GD&T to control the position of the holes.

    I nuovi disegni usano il GD&T per controllare la posizione dei fori.

    Our quality engineers attended a two-day GD&T training course.

  13. 13

    datum(noun)

    /ˈdeɪtəm/

    riferimento, superficie di riferimento

    a reference point, line or surface on a part from which other features are measured

    All hole positions are measured from datum A, the bottom face.

    Tutte le posizioni dei fori sono misurate dal riferimento A, la faccia inferiore.

    Clamp the part on its datum surface before machining.

  14. 14

    surface roughness(noun)

    /ˈsɜːfɪs rʌfnəs/

    rugosità superficiale, rugosità

    the small peaks and valleys on a machined surface, usually given as an Ra value in micrometres

    The seal face needs a surface roughness of Ra 0.4 or better.

    La superficie di tenuta richiede una rugosità superficiale di Ra 0,4 o migliore.

    A worn insert increased the surface roughness of the bore.

  15. 15

    fillet(noun)

    /ˈfɪlɪt/

    raccordo, raggio di raccordo

    a rounded inside corner between two surfaces, used to reduce stress and make parts stronger

    A larger fillet at the shoulder will reduce the risk of cracking.

    Un raccordo più grande sullo spallamento ridurrà il rischio di cricche.

    All internal corners have a 2 mm fillet unless stated otherwise.

  16. 16

    bill of materials(noun)

    /ˌbɪl əv məˈtɪəriəlz/

    distinta base, DB

    a list of all the parts, materials and quantities needed to build a product

    Purchasing orders parts directly from the bill of materials.

    L'ufficio acquisti ordina i componenti direttamente dalla distinta base.

    The bill of materials lists 48 parts for the conveyor drive.