Lumaktaw sa nilalaman

Aralin 4/10 · 16 salita · 0 natutunan

Technical drawings and tolerances

Mga teknikal na drowing at tolerance

  1. 1

    dimension(noun)

    /daɪˈmenʃn/

    sukat, dimensyon

    a measurement of length, width, height, diameter or angle that is shown on a drawing

    This dimension is critical, so measure it on every part.

    Kritikal ang sukat na ito, kaya sukatin ito sa bawat piyesa.

    The overall dimensions of the frame are 1200 by 800 millimetres.

    Kasingkahulugansizemeasurementextentscopeaspectmagnitude
    Kasalungatinsignificanceunimportanceminorityreduction
  2. 2

    chamfer(noun)

    /ˈtʃæmfər/

    tsamper, bevel

    a small angled cut along an edge or corner to remove sharpness or help parts fit together

    Add a 0.5 mm chamfer to all outside edges.

    Magdagdag ng 0.5 mm na tsamper sa lahat ng panlabas na gilid.

    The chamfer on the shaft end helps the bearing slide on.

    Kasingkahuluganbevelcantsplayslopeangle
    Kasalungatsquare edgeright angleperpendicular
  3. 3

    technical drawing(noun)

    /ˌteknɪkl ˈdrɔːɪŋ/

    teknikal na guhit, dibuhong teknikal

    an exact drawing that shows the shape, size, material and requirements of a part so it can be made

    Every machinist must be able to read a technical drawing.

    Dapat marunong bumasa ng teknikal na guhit ang bawat machinist.

    Check that you have the latest technical drawing before you start cutting.

  4. 4

    CAD(abbreviation)

    /kæd/

    CAD, disenyong tinutulungan ng kompyuter

    computer-aided design: using software to create and change drawings and 3D models of parts

    The designer sent us the CAD model of the new bracket.

    Ipinadala sa amin ng designer ang CAD model ng bagong bracket.

    We use CAD software to check that the parts fit before ordering material.

  5. 5

    orthographic projection(noun)

    /ˌɔːθəˌɡræfɪk prəˈdʒekʃn/

    ortograpikong proyeksiyon

    a way of drawing an object as several flat views, such as front, top and side, at right angles

    European technical drawings normally use first-angle orthographic projection.

    Karaniwang gumagamit ng first-angle na ortograpikong proyeksiyon ang mga teknikal na guhit sa Europa.

    The part is shown in orthographic projection with three views.

  6. 6

    section view(noun)

    /ˈsekʃn vjuː/

    tanaw na hiwa, hiwang tanaw

    a view on a drawing that shows the inside of a part as if it had been cut through

    Add a section view so the machinist can see the internal groove.

    Magdagdag ng tanaw na hiwa upang makita ng machinist ang panloob na uka.

    Section view B-B shows the depth of the blind hole.

  7. 7

    assembly drawing(noun)

    /əˈsembli drɔːɪŋ/

    guhit ng asembliya, guhit ng pagkakabit

    a drawing that shows how all the parts of a product fit together, usually with a parts list

    Follow the assembly drawing to fit the bearings in the correct order.

    Sundin ang guhit ng asembliya upang ikabit ang mga bearing sa tamang pagkakasunod-sunod.

    Item numbers on the assembly drawing match the bill of materials.

  8. 8

    title block(noun)

    /ˈtaɪtl blɒk/

    kahon ng pamagat

    the box on a drawing that gives the part name, number, material, scale, revision and approval

    The revision letter is shown in the title block at the bottom right.

    Nakasaad ang titik ng rebisyon sa kahon ng pamagat sa kanang ibaba.

    Check the material in the title block before you order stock.

  9. 9

    tolerance(noun)

    /ˈtɒlərəns/

    toleransiya, pinahihintulutang paglihis

    the amount a dimension is allowed to vary from its stated size and still be acceptable

    The bore diameter has a tolerance of plus or minus 0.01 millimetres.

    Ang diyametro ng butas ay may toleransiya na plus o minus 0.01 milimetro.

    Three shafts were rejected because they were out of tolerance.

  10. 10

    clearance fit(noun)

    /ˈklɪərəns fɪt/

    maluwag na pagkakasya, pagkakasyang may luwang

    a fit where the hole is always slightly larger than the shaft, so the parts can move or slide

    The pin has a clearance fit so it can rotate freely in the hole.

    May maluwag na pagkakasya ang pin kaya malayang makaiikot ito sa butas.

    Use a clearance fit for parts that must be removed often.

  11. 11

    interference fit(noun)

    /ˌɪntəˈfɪərəns fɪt/

    mahigpit na pagkakasya, pagkakasyang may diin

    a fit where the shaft is slightly larger than the hole, so the parts must be pressed or heated together

    The bearing is mounted with an interference fit on the shaft.

    Nakakabit ang bearing sa shaft sa pamamagitan ng mahigpit na pagkakasya.

    We heated the gear to assemble the interference fit without damage.

  12. 12

    GD&T(abbreviation)

    /ˌdʒiː diː ən ˈtiː/

    GD&T, heometrikong sukat at toleransiya

    geometric dimensioning and tolerancing: a system of symbols on drawings that controls form, orientation and position of features

    The new drawings use GD&T to control the position of the holes.

    Gumagamit ang mga bagong guhit ng GD&T upang kontrolin ang posisyon ng mga butas.

    Our quality engineers attended a two-day GD&T training course.

  13. 13

    datum(noun)

    /ˈdeɪtəm/

    batayang sanggunian, batayang ibabaw

    a reference point, line or surface on a part from which other features are measured

    All hole positions are measured from datum A, the bottom face.

    Lahat ng posisyon ng butas ay sinusukat mula sa datum A, ang ilalim na mukha.

    Clamp the part on its datum surface before machining.

  14. 14

    surface roughness(noun)

    /ˈsɜːfɪs rʌfnəs/

    kagaspangan ng ibabaw

    the small peaks and valleys on a machined surface, usually given as an Ra value in micrometres

    The seal face needs a surface roughness of Ra 0.4 or better.

    Kailangan ng seal face ng kagaspangan ng ibabaw na Ra 0.4 o mas makinis.

    A worn insert increased the surface roughness of the bore.

  15. 15

    fillet(noun)

    /ˈfɪlɪt/

    bilugang sulok, radyus ng sulok

    a rounded inside corner between two surfaces, used to reduce stress and make parts stronger

    A larger fillet at the shoulder will reduce the risk of cracking.

    Ang mas malaking bilugang sulok sa balikat ay magpapababa ng panganib ng pagbitak.

    All internal corners have a 2 mm fillet unless stated otherwise.

  16. 16

    bill of materials(noun)

    /ˌbɪl əv məˈtɪəriəlz/

    talaan ng mga materyales, BOM

    a list of all the parts, materials and quantities needed to build a product

    Purchasing orders parts directly from the bill of materials.

    Direktang nag-o-order ng mga piyesa ang purchasing mula sa talaan ng mga materyales.

    The bill of materials lists 48 parts for the conveyor drive.